Improved Electrochemical Performance of 0.5Li2MnO3·0.5LiNi0.5Mn0.5O2 Cathode Materials for Lithium Ion Batteries Synthesized by Ionic-Liquid-Assisted Hydrothermal Method
Yanhong Xiang1 
Youliang Jiang1 Saiqiu Liu1 Jianhua Wu1 Zhixiong Liu1 Ling Zhu1 Lizhi Xiong2 Zeqiang He2 
Xianwen Wu3*- 1School of Physics and Mechanical and Electrical Engineering, Jishou University, Jishou, China
- 2College of Biology and Environmental Sciences, Jishou University, Jishou, China
- 3School of Chemistry and Chemical Engineering, Jishou University, Jishou, China
Well-dispersed Li-rich Mn-based 0.5Li2MnO3·0.5LiNi0.5Mn0.5O2 nanoparticles with diameter ranging from 50 to 100 nm are synthesized by a hydrothermal method in the presence of N-hexyl pyridinium tetrafluoroborate ionic liquid ([HPy][BF4]). The microstructures and electrochemical performance of the prepared cathode materials are characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and electrochemical measurements. The XRD results show that the sample prepared by ionic-liquid-assisted hydrothermal method exhibits a typical Li-rich Mn-based pure phase and lower cation mixing. SEM and TEM images indicate that the extent of particle agglomeration of the ionic-liquid-assisted sample is lower compared to the traditional hydrothermal sample. Electrochemical test results indicate that the materials synthesized by ionic-liquid-assisted hydrothermal method exhibit better rate capability and cyclability. Besides, electrochemical impedance spectroscopy (EIS) results suggest that the charge transfer resistance of 0.5Li2MnO3· 0.5LiNi0.5Mn0.5O2 synthesized by ionic-liquid-assisted hydrothermal method is much lower, which enhances the reaction kinetics.
Introduction
Rechargeable lithium-ion batteries (LIBs) have conquered the electronics field due to its many advantages such as high energy and power density, largest output voltage, long cyclic life, and environmental friendliness, compared to other rechargeable batteries (Zhou et al., 2016; Nie et al., 2020; Shi et al., 2020; Tang et al., 2020). However, owing to the rapid development of electric vehicles, portable electronics, and stationary energy storage devices, new advances in performances/safety/costs are needed (Li et al., 2017; Lu et al., 2017; Yang et al., 2019; Guo et al., 2020; Zheng et al., 2020a). Therefore, the alternative cathode materials with high specific capacities have been extensively explored. Compared with the conventional commercial cathode materials, layered lithium-rich manganese-based cathode materials, xLi2MnO3·(1 – x)LiMO2 (M = Mn, Ni, Co, etc.), which consist of two components of α-NaFeO2-structured LiMO2 (R-3m symmetry) phase and monoclinic Li2MnO3 (C2/m symmetry) phase, have attracted extensive interest due to their low price and higher discharge capacity of more than 250 mA h g−1 (Lin et al., 2008; Yan et al., 2014; Nayak et al., 2018; Yang et al., 2018; Xiang et al., 2019; Gao et al., 2020; Jiang et al., 2020; Zhao et al., 2020). However, several drawbacks, including intrinsic poor capability, poor cycling stability, and voltage fading, hindered its practical applications (Song et al., 2016; Xiang et al., 2017; Hu et al., 2019; Zhang et al., 2019; Sigel et al., 2020).
To solve these problems, plenty of efforts have been made to realize electrochemical performance improvement, including synthesizing strategies (Hua et al., 2019; Redel et al., 2019), elemental doping (Yu et al., 2019; Zheng et al., 2020b), and surface modification (Liu et al., 2019; Peng et al., 2020; Zhong et al., 2020). Many research groups have recently adopted different synthetic methods to improve the electrochemical performance of Li-rich Mn-based layered cathode materials because of the optimization of suitable morphologies and sizes, such as coprecipitation method, sol–gel, and hydrothermal method (Pimenta et al., 2017). Among these methods, the hydrothermal method is promising since it has many advantages over other methods, such as homogeneous mixing at the atomic or molecular level, high purity, and small particle size. Usually, lowering the particle size can considerably meet the improvement of the rate capability (Deng et al., 2020). However, the hydrothermal method has several drawbacks such as uneven distribution and serious agglomeration.
Ionic liquids (ILs), which are room temperature molten salts, consisting of organic cations and inorganic anions, have been recently used to synthesize nanomaterials with desirable structures and morphologies due to their unique physical and chemical properties (Li et al., 2008). Therefore, we use the [HPy][BF4] ionic liquid as both solvent and template to enable the growth of 0.5Li2MnO3·0.5LiNi0.5Mn0.5O2 powders with controlled size and morphology, which are expected to improve the rate capability of this material. The microstructures and electrochemical performance of the prepared cathode materials are investigated.
Experimental
Materials Synthesis
All the raw materials were analytical reagent and used without further purification. 0.5Li2MnO3·0.5LiNi0.5Mn0.5O2 was prepared by ionic-liquid-assisted hydrothermal method as follows (Figure 1). A stoichiometric amount of Ni(CH3COO)2·4H2O and Mn(CH3COO)2·4H2O together with 1 g of [HPy][BF4] ionic liquid was dissolved in deionized water. The NH4HCO3 aqueous solution, which was used as the precipitation reagent, was pumped into the obtained mixed solution drop by drop under magnetic stirring. Finally, the resultant mixture was sealed into a 100-ml Teflon-lined stainless steel autoclave and maintained at 180°C for 12 h. After being cooled down to ambient temperature, the suspension was filtered, and the precipitated powders were washed and then dried at 105°C for 5 h. The obtained carbonate precursors were thoroughly mixed with a 3-wt% excess of a stoichiometric amount of Li2CO3 to offset the possible evaporative of lithium occurring at high temperature and then calcined at 700°C for 10 h in air. At the same time, the sample without adding ionic liquid was synthesized for comparison.
Figure 1. Illustration of the formation of 0.5Li2MnO3·0.5LiNi0.5Mn0.5O2 nanoparticles with ionic-liquid-assisted hydrothermal method.
Characterization
Thermogravimetric (TG) and differential scanning calorimetry (DSC) analysis was tested by an SDTQ600 analyzer, at a rate of 10°C min−1 under air conditions in the temperature range of 25–900°C. The crystal nature of materials was identified by X-ray diffraction (XRD, Rigaku 2500, Japan) with Cu-Kα radiation. The particle morphology, size, and distribution of the as-synthesized powders were observed by scanning electron microscopy (SEM, JEOL JSM-5600LV) and transmission electron microscopy (TEM, Tecnai G12).
Electrochemical Test
The electrode slurry was prepared by mixing 0.5Li2MnO3·0.5LiNi0.5Mn0.5O2 power, carbon black, and polyvinylidene difluoride (PVDF) with a weight ratio of 8:1:1 in N-methyl-2-pyrrolidone (NMP). The slurry was cast onto an Al foil and then cut into a circular electrode after dried. The testing coin-type cells (CR2032) of Li | LiPF6 (EC/DEC/DMC = 1:1:1 by volume) | 0.5Li2MnO3·0.5LiNi0.5Mn0.5O2 were assembled in an argon-filled glove box. The cathode and anode electrodes were separated by Celgard 2400 films. The charge–discharge texts were carried out by using the LAND-CT2001A battery text system (Wuhan, China). The electrochemical impedance spectroscopy (EIS) was tested by an electrochemical workstation CHI660E over a frequency range of 100 kHz to 0.01 Hz.
Results and Discussion
Figure 2 shows the TG-DSC patterns of the mixture of Li2CO3 and the precursor synthesized by ionic-liquid-assisted hydrothermal method. There are three weight losses that appear at 80–100°C, 220–350°C, and 600–640°C in the TG-DSC patterns, respectively, which correspond to the evaporation of free water, the decomposition of the mixture and a small amount of residual ionic liquids, and the formation of lattice oxides, respectively. Therefore, 700°C is chosen as the sintering temperature.
Figure 2. Thermogravimetric–differential scanning calorimetry (TG-DSC) curves of the mixture of Li2CO3 and the precursor synthesized by ionic-liquid-assisted hydrothermal method.
Figure 3 compares the XRD patterns of 0.5Li2MnO3·0.5LiNi0.5Mn0.5O2 precursor synthesized by the traditional hydrothermal method (TH-LMNO) and ionic-liquid-assisted hydrothermal method (ILH-LMNO). The crystal lattice of both samples can be approximated to the hexagonal α-NaFeO2-type structure (R-3m) according to the strong diffraction peaks, except for the low-intensity peaks at 20–25°, corresponding to a monoclinic Li2MnO3 phase (C2/m symmetry) (Thackeray et al., 2006, 2007; Johnson et al., 2008), is highlighted in Figure 3. The obvious split (006)/(102) and (108)/(110) peaks indicate that the synthesized powders have a good layered structure. No peaks of any impurity phase are detected in the XRD patterns of the ILH-LMNO sample, indicating that the ionic liquid has no effects on the crystal structure of the final materials. The ratio (R) of I(003)/I(104) is used to determine the degree of cation mixing of layered structure. When the R value is >1.2, it is suggested that the degree of cation mixing is small and the materials have an excellent hexagonal layered structure. The R value of the ILH-LMNO sample is 1.61, larger than the value of the TH-LMNO sample (1.40), suggesting a low cation mixing and better crystalline structure, which implies excellent rate capability and cyclic performance.
Figure 3. The X-ray diffraction (XRD) patterns of (a) TH-LMNO and (b) ILH-LMNO.
Scanning electron microscopy images of TH-LMNO and ILH-LMNO are examined and shown in Figure 4. Compared with the obvious agglomeration particles for the TH-LMNO sample, the primary particles of the ILH-LMNO sample are more uniform and dispersed. The molecules of [HPy][BF4] can be adsorbed on the surfaces of the particles during the formation process of precursor, preventing the particles aggregating mutually due to their relative large organic cations (C11H18N+), which act as barriers. Figure 1 shows schematic effect of [HPy][BF4] and formation process of 0.5Li2MnO3•0.5LiNi0.5Mn0.5O2. Due to the template function of the [HPy][BF4] ionic liquid, a large number of pores formed as well as smaller, more uniform particles obtained. The aggregates of the ILH-LMNO sample are arranged in chains, and the particles are distributed in a narrow range of 50–100 nm. In general, the small size of the nanoparticles will reduce the diffusion path of Li+ ions and electrons and thus enhance the rate capability of the materials (Wu et al., 2017; Zhao et al., 2018). The morphologies and microstructures of the ILH-LMNO sample were further clarified by high resolution TEM (HRTEM) characterization. The width between lattice fringes in Figure 4e is 0.47 nm, which correspond to the (003) plane of the LiNi0.5Mn0.5O2-layered structure (R-3m) or (001) plane of the Li2MnO3 superlattice structure (C-2m), while the width between lattice fringes in Figure 4f is 0.207 nm, corresponding to the (104) plane of the LiNi0.5Mn0.5O2-layered structure or (202) plane of the Li2MnO3 superlattice structure, demonstrating that the lithium-rich manganese-based 0.5Li2MnO3·0.5LiNi0.5Mn0.5O2 materials can be successfully prepared by the ionic-liquid-assisted hydrothermal method.
Figure 4. The scanning electron microscopy (SEM) images of (a,b) TH-LMNO and (c,d) ILH-LMNO. The transmission electron microscopy (TEM) images of (e,f) ILH-LMNO.
Electrochemical evaluations of the TH-LMNO and ILH-LMNO electrodes are performed in lithium coin-type cells. Figure 5 shows the typical voltage profiles and the dQ/dV plots of the initial charge/discharge of TH-LMNO and ILH-LMNO at 0.05 C (25 mA g−1) between 2.0 and 4.8 V. As can be seen, all the charging profiles in the figure are composed of two regions, which correspond to the two prominent anodic peaks in the dQ/dV curves. The slope region below 4.5 V is due to the extraction of Li+ ions from the LiNi0.5Mn0.5O2 component with Ni oxidation from Ni2+ to Ni4+. The other plateau region above 4.5 V is attributed to the removal of Li2O from the layered Li2MnO3 component with “MnO2-like” activation, which results in not only the extraordinary capacity but also the larger initial irreversible capacity loss offered by Li-rich materials (Oishi et al., 2015; Assat and Tarascon, 2018). Both the cell with TH-LMNO and ILH-LMNO have three reduction prominent peaks during the initial discharge process at 3.2, 3.7, and 4.3 V, except an additional Li uptake peak at 2.3 V for the TH-LMNO sample, which can be assigned to a spinel phase (Riekehr et al., 2016). The cation distribution of the ILH-LMNO sample is uniform, and there has no heterogeneous production, so there is no peak at 2.3 V. The peaks at ~4.3 and ~3.7 V can be attributed to the Ni4+/3+/2+ reduction, and the peak around 3.2 V is associated with the Mn4+/3+ reduction (Johnson et al., 2008; Chen et al., 2015). ILH-LMNO electrode provided a significantly higher capacity (254.1 mA h g−1) together with superior first-cycle efficiency (74.4%) as compared to the TH-LMNO electrode (242.9 mA h g−1, 72.1%).
Figure 5. The initial charge/discharge curves (I) and the dQ/dV plots (II) of (a) TH-LMNO and (b) ILH-LMNO (4.8–2.0 V, 25 mA g−1).
To further identify and understand the redox reactions between the first and the following cycles, the evolution of dQ/dV profiles corresponding to the 1st, 2nd, 5th, and 50th cycles of TH-LMNO and ILH-LMNO are provided in Figure 6. It is clearly found from the dQ/dV curves that the peak above 4.5 V in the initial cycle is irreversible and disappears in the subsequent cycles, demonstrating that the activation of Li2MnO3 component is irreversible. Meanwhile, all the reduction peaks shift continuously to a lower voltage upon cycles, which is attributed to the voltage decay due to layered-to-spinel phase transitions (Yu et al., 2019). It can be seen that the Ni4+/3+/2+ reduction peaks decrease more significantly upon cycles for the TH-LMNO sample compared with the ILH-LMNO sample. In addition, the reduction peak of Mn4+/3+ at ~3.2 V decreased 0.75 V after the 50th cycle for the TH-LMNO sample, while the reduction peak decreased only 0.42 V for the ILH-LMNO sample. All the above characteristics illustrate that the ILH-LMNO sample has better capacity and voltage retention, which is mainly due to the more uniform particles and better cation arrangement of the ILH-LMNO sample.
Figure 6. The dQ/dV plots of (A) TH-LMNO and (B) ILH-LMNO.
The rate capabilities and cycle performances of TH-LMNO and ILH-LMNO are shown in Figure 7. The current density was increased from 25 mA g−1 (0.05 C) to 500 mA g−1 (1.0 C) and then switched back to 50 mA g−1 (0.1 C). At each rate, the capacity of the ILH-LMNO sample is higher than that of the TH-LMNO sample. These could be attributed to the uniform nanoparticles for the ILH-LMNO sample, which shorten lithium-ion diffusion pathway. When the electrodes are cycled and switched back from 1.0 to 0.1 C, the capacities returned to the initial value, which implied the structural stability of both samples even at a high rate. As displayed in Figure 7, the capacity of the ILH-LMNO sample is also 215.9 mA h g−1 after the 65th cycle, with a capacity retention of 94.3% (compared with the first 0.1 C capacity), while the TH-LMNO sample delivered 180.9 mA h g−1 with a capacity retention of 85.2%. The obvious capacity degradation observed for the TH-LMNO sample can be attributed to the large particles that possibly limited the lithium-ion diffusion and led to electrochemically inactivated core. The excellent cycling performance of the ILH-LMNO sample is due to the fact that the material belongs to the micro–nanostructure, which is beneficial for the structure stability without apparent kinetic disadvantages.
Figure 7. The rate capabilities and cycle performances of (a) TH-LMNO and (b) ILH-LMNO (4.8–2.0 V).
To get insight into the kinetics of the electrode process, EIS of TH-LMNO and ILH-LMNO at the pristine state are measured and shown in Figure 8. These Nyquist plots are well fitted based on the equivalent circuit presented as inset in Figure 8. Rs and Rct refers to the solution resistance and charge-transfer resistance due to the lithium-ion insertion reaction in the electrode/electrolyte interface, respectively, CPE indicates the double-layer capacitance, and Wo represents the Warburg impedance (Wu et al., 2019; Xiang et al., 2019). According to the fitting results, it is found that the Rct value of the ILH-LMNO sample is relatively smaller (155.6 Ω) than that of the TH-LMNO sample (474.6 Ω), which may benefit from the well-dispersed nanoparticles of the ILH-LMNO sample.
Figure 8. The Nyquist plots of (a) TH-LMNO and (b) ILH-LMNO at the pristine state.
Conclusion
Nano-0.5Li2MnO3·0.5LiNi0.5Mn0.5O2 cathode materials are synthesized by ionic-liquid-assisted hydrothermal method. XRD results show that the degree of cation mixing and crystalline structure is improved by the ionic liquid during the synthesis. SEM and TEM characterizations suggest that the particles of the materials prepared by the ionic-liquid-assisted hydrothermal method are more uniform and less agglomerated than those prepared by the traditional hydrothermal method. Electrochemical test results indicate that the presence of ionic liquid during the synthesis have a significant effect on the rate capability and cyclability. The 0.5Li2MnO3·0.5LiNi0.5Mn0.5O2 synthesized by the ionic-liquid-assisted hydrothermal method exhibited a higher initial capacity of 254.1 mA h g−1, and the capacity retention after 65 cycles was 94.3%. Besides, the EIS data show that the ionic-liquid-assisted hydrothermal sample have a relatively smaller charge transfer resistance value and thus reduces the diffusion pathways of Li+ ions and electrons, which is well consistent with the rate capability test results.
Data Availability Statement
All datasets generated for this study are included in the article/supplementary material.
Author Contributions
All authors listed have made a substantial, direct and intellectual contribution to the work, and approved it for publication.
Funding
This work was supported by the National Natural Science Foundation of China (Nos. 51662010, 51762017, 51704124, 51672104, and 51862008), the National Natural Science Foundation of Hunan Province, China (Nos. 2020JJ5457 and 2017JJ2216), the Educational Commission of Hunan Province, China (Nos. 19A416 and S201910531053), the Research Foundation of Jishou University of Hunan Province, China (Nos. JDLF2019003 and Jdx1843), and the Program of Youth Talent Support for Hunan Province (No. 2018RS3098).
Conflict of Interest
The authors declare that the research was conducted in the absence of any commercial or financial relationships that could be construed as a potential conflict of interest.
References
Assat, G., and Tarascon, J. M. (2018). Fundamental understanding and practical challenges of anionic redox activity in Li-ion batteries. Nat. Energy 3, 373–386. doi: 10.1038/s41560-018-0097-0
Chen, D., Yu, Q., Xiang, X., Chen, M., Chen, Z., Song, S., et al. (2015). Porous layered lithium-rich oxide nanorods: Synthesis and performances as cathode of lithium ion battery. Electrochim. Acta 154, 83–93. doi: 10.1016/j.electacta.2014.12.037
Deng, C., Xie, X., Han, J., Tang, Y., Gao, J., Liu, C., et al. (2020). A sieve-functional and uniform-porous kaolin layer toward stable zinc metal anode. Adv. Funct. Mater. 30:2000599. doi: 10.1002/adfm.202000599
Gao, J., Yuan, T., Luo, S., Ruan, J., Sun, H., Yang, J., et al. (2020). Boosting lithium ion storage of lithium nickel manganese oxide via conformally interfacial nanocoating. J. Colloid Interf. Sci. 570, 153–162. doi: 10.1016/j.jcis.2020.02.112
Guo, X., Zhou, J., Bai, C., Li, X., Fang, G., and Liang, S. (2020). Zn/MnO2 battery chemistry with dissolution-deposition mechanism. Mater.Today Energy 16:100396. doi: 10.1016/j.mtener.2020.100396
Hu, S., Pillai, A. S., Liang, G., Pang, W. K., Wang, H., Li, Q., et al. (2019). Li-rich layered oxides and their practical challenges: recent progress and perspectives. Electrochem. Energy Rev. 2, 277–311. doi: 10.1007/s41918-019-00032-8
Hua, W., Chen, M., Schwarz, B., Knapp, M., Bruns, M., Barthel, J., et al. (2019). Lithium/oxygen incorporation and microstructural evolution during synthesis of Li-rich layered Li[Li0.2Ni0.2Mn0.6]O2 oxides. Adv. Energy Mater. 9:1803094. doi: 10.1002/aenm.201803094
Jiang, Z., Li, Y., Han, C., Huang, Z., Wu, X., He, Z., et al. (2020). Raising lithium storage performances of NaTi2(PO4)3 by nitrogen and sulfur dual-doped carbon layer. J. Electrochem. Soc. 167:020550. doi: 10.1149/1945-7111/ab6c5c
Johnson, C. S., Li, N., Lefief, C., Vaughey, J. T., and Thackeray, M. M. (2008). Synthesis, Characterization and electrochemistry of lithium battery electrodes xLi2MnO3 (1- x)LiMn0.333Ni0.333Co0.333O2 (0 ≤ x ≤ 0.7). Chem. Mater. 20, 6095–6106. doi: 10.1021/cm801245r
Li, X., Qian, K., He, Y. B., Liu, C., An, D., Li, Y., et al. (2017). A dual-functional gel-polymer electrolyte for lithium ion batteries with superior rate and safety performances. J. Mater. Chem. A. 5, 18888–18895. doi: 10.1039/C7TA04415A
Li, Z., Jia, Z., Luan, Y., and Mu, T. (2008). Ionic liquids for synthesis of inorganic nanomaterials. Curr. Opin. Solid St. M. 12, 1–8. doi: 10.1016/j.cossms.2009.01.002
Lin, Y., Gao, M. X., Zhu, D., Liu, Y. F., and Pan, H. G. (2008). Effects of carbon coating and iron phosphides on the electrochemical properties of LiFePO4/C. J. Power Sources 184, 444–448. doi: 10.1016/j.jpowsour.2008.03.026
Liu, Y., Fan, X., Zhang, Z., Wu, H., Liu, D., Dou, A., et al. (2019). Enhanced electrochemical performance of Li-rich layered cathode materials by combined Cr doping and LiAlO2 coating. ACS Sustain. Chem. Eng. 7, 2225–2235. doi: 10.1021/acssuschemeng.8b04905
Lu, Q., He, Y. B., Yu, Q., Li, B., Kaneti, Y. V., Yao, Y., et al. (2017). Dendrite-free, high-rate, long-life lithium metal batteries with a 3D cross-linked network polymer electrolyte. Adv. Mater. 29:201604460. doi: 10.1002/adma.201604460
Nayak, P. K., Erickson, E. M., Schipper, F., Penki, T. R., Munichandraiah, N., Adelhelm, P., et al. (2018). Review on challenges and recent advances in the electrochemical performance of high capacity Li- and Mn-Rich cathode materials for Li-ion batteries. Adv. Energy Mater. 8, 1702397–1702412. doi: 10.1002/aenm.201702397
Nie, Y., Xiao, W., Miao, C., Xu, M., and Wang, C. (2020). Effect of calcining oxygen pressure gradient on properties of LiNi0.8Co0.15Al0.05O2 cathode materials for lithium ion batteries. Electrochim. Acta. 334:135654. doi: 10.1016/j.electacta.2020.135654
Oishi, M., Yogi, C., Watanabe, I., Ohta, T., Orikasa, Y., Uchimoto, Y., et al. (2015). Direct observation of reversible charge compensation by oxygen ion in Li-rich manganese layered oxide positive electrode material, Li1.16Ni0.15Co0.19Mn0.50O2. J. Power Sources 276, 89–94. doi: 10.1016/j.jpowsour.2014.11.104
Peng, H., Zhao, S. X., Huang, C., Yu, L. Q., Fang, Z. Q., and Wei, G. D. (2020). In Situ construction of spinel coating on the surface of a lithium-rich manganese-based single crystal for inhibiting voltage fade. ACS Appl. Mater. Inter. 12, 11579–11588. doi: 10.1021/acsami.9b21271
Pimenta, V., Sathiya, M., Batuk, D., Abakumov, A. M., Giaume, D., Cassaignon, S., et al. (2017). Synthesis of Li-rich NMC: a comprehensive study. Chem. Mater. 29, 9923–9936. doi: 10.1021/acs.chemmater.7b03230
Redel, K., Kulka, A., Plewa, A., and Molenda, J. (2019). High-performance Li-rich layered transition metal oxide cathode materials for Li-ion batteries. J. Electrochem. Soc. 166, A5333–A5342. doi: 10.1149/2.0511903jes
Riekehr, L., Liu, J., Schwarz, B., Sigel, F., Kerkamm, I., Xia, Y., et al. (2016). Effect of pristine nanostructure on first cycle electrochemical characteristics of lithium-rich lithium-nickel-cobalt-manganese-oxide cathode ceramics for lithium ion batteries. J. Power Sources 306, 135–147. doi: 10.1016/j.jpowsour.2015.11.082
Shi, X., Pang, Y., Wang, B., Sun, H., Wang, X., Li, Y., et al. (2020). In situ forming LiF nanodecorated electrolyte/electrode interfaces for stable all-solid-state batteries, Mater. Today Nano. 10, 100079–100087. doi: 10.1016/j.mtnano.2020.100079
Sigel, F., Schwarz, B., Kleiner, K., Dräger, C., Esmezjan, L., Yavuz, M., et al. (2020). Thermally induced structural reordering in Li- and Mn-rich layered oxide Li ion cathode materials. Chem. Mater. 32, 1210–1223. doi: 10.1021/acs.chemmater.9b04355
Song, L., Tang, Z., Chen, Y., Xiao, Z., Li, L., Zheng, H., et al. (2016). Structural analysis of layered Li2MnO3-LiMO2 (M=Ni1/3Mn1/3Co1/3, Ni1/2Mn1/2) cathode materials by Rietveld refinement and first-principles calculations. Ceram. Int. 42, 8537–8544. doi: 10.1016/j.ceramint.2016.02.080
Tang, F., Gao, J., Ruan, Q., Wu, X., Wu, X., Zhang, T., et al. (2020). Graphene-wrapped MnO/C composites by MOFs-derived as cathode material for aqueous zinc ion batteries. Electrochim. Acta. 353, 136570. doi: 10.1016/j.electacta.2020.136570
Thackeray, M. M., Kang, S. H., Johnson, C. S., Vaughey, J. T., Benedek, R., and Hackney, S. A. (2007). Li2MnO3-stabilized LiMO2 (M = Mn, Ni, Co) electrodes for lithium-ion batteries. J. Mater. Chem. 17, 3112–3125. doi: 10.1039/b702425h
Thackeray, M. M., Kang, S. H., Johnson, C. S., Vaughey, J. T., and Hackney, S. A. (2006). Comments on the structural complexity of lithium-rich Li1+xM1−xO2 electrodes (M=Mn, Ni, Co) for lithium batteries. Electrochem. Commun. 8, 1531–1538. doi: 10.1016/j.elecom.2006.06.030
Wu, X., Li, Y., Zhao, S., Zeng, F., Peng, X., Xiang, Y., et al. (2019). Fabrication of F-doped, C-coated NiCo2O4 nanocomposites and its electrochemical performances for lithium-ion batteries. Solid State Ionics 334, 48–55. doi: 10.1016/j.ssi.2019.01.039
Wu, X., Xiang, Y., Peng, Q., Wu, X., Li, Y., Tang, F., et al. (2017). Green-low-cost rechargeable aqueous zinc-ion batteries using hollow porous spinel ZnMn2O4 as the cathode material. J. Mater. Chem. A 5, 17990–17997. doi: 10.1039/C7TA00100B
Xiang, Y., Li, J., Liao, Q., and Wu, X. (2019). Morphology and particle growth of Mn-based carbonate precursor in the presence of ethylene glycol for high-capacity Li-rich cathode materials. Ionics 25, 81–87. doi: 10.1007/s11581-018-2569-4
Xiang, Y., Sun, Z., Li, J., Wu, X., Liu, Z., Xiong, L., et al. (2017). Improved electrochemical performance of Li1.2Ni0.2Mn0.6O2 cathode material for lithium ion batteries synthesized by the polyvinyl alcohol assisted sol-gel method. Ceram. Int. 43, 2320–2324. doi: 10.1016/j.ceramint.2016.11.016
Yan, J., Liu, X., and Li, B. (2014). Recent progress in Li-rich layered oxides as cathode materials for Li-ion batteries. RSC Adv. 4, 63268–63284. doi: 10.1039/C4RA12454E
Yang, P., Li, H., Wei, X., Zhang, S., and Xing, Y. (2018). Structure tuned Li1.2Mn0.6Ni0.2O2 with low cation mixing and Ni segregation as high performance cathode materials for Li-ion batteries. Electrochim. Acta 271, 276–283. doi: 10.1016/j.electacta.2018.01.104
Yang, S., Zhang, M., Wu, X., Wu, X., Zeng, F., Li, Y., et al. (2019). The excellent electrochemical performances of ZnMn2O4/Mn2O3: The composite cathode material for potential aqueous zinc ion batteries. J. Electroanal. Chem. 832, 69–74. doi: 10.1016/j.jelechem.2018.10.051
Yu, Z., Ning, F., Li, B., Sun, Z., Chu, W., and Xia, D. (2019). Mitigating voltage decay of Li-rich layered oxide by incorporation of 5d metal rhenium. J. Phys. Chem. C. 123, 18870–18876. doi: 10.1021/acs.jpcc.9b05683
Zhang, K., Li, B., Zuo, Y., Song, J., Shang, H., Ning, F., et al. (2019). Voltage decay in layered Li-rich Mn-based cathode materials. Electrochem. Energy Rev. 2, 606–623. doi: 10.1007/s41918-019-00049-z
Zhao, L., Wu, H. H., Yang, C., Zhang, Q., Zhong, G., Zheng, Z., et al. (2018). Mechanistic origin of the high performance of Yolk@Shell Bi2S3@N-doped carbon nanowire electrodes. ACS Nano. 12, 12597–12611. doi: 10.1021/acsnano.8b07319
Zhao, S., Yan, K., Zhang, J., Sun, B., and Wang, G. (2020). Reviving reaction mechanism of layered lithium-rich cathode materials for high-energy lithium-ion battery. Angew. Chem. Int. Edit. doi: 10.1002/anie.202000262. [Epub ahead of print].
Zheng, S., Dou, A., Su, M., and Liu, Y. (2020a). Influence of Nb doping on electrochemical performance of nanostructured cation disordered Li1+x/100Ni1/2−x/100Ti1/2−x/100Nbx/100O(2) composites cathode for Li-ion batteries. J. Nanosci. Nanotechno. 20, 452–459. doi: 10.1166/jnn.2020.16884
Zheng, Z., Li, P., Huang, J., Liu, H., Zao, Y., Hu, Z., et al. (2020b). High performance columnar-like Fe2O3@carbon composite anode via yolk@shell structural design. J. Energy Chem. 41, 126–134. doi: 10.1016/j.jechem.2019.05.009
Zhong, J., Yang, Z., Yu, Y., Liu, Y., Li, J., and Kang, F. (2020). Surface substitution of polyanion to improve structure stability and electrochemical properties of lithium-rich layered cathode oxides. Appl. Surf. Sci. 512:145741. doi: 10.1016/j.apsusc.2020.145741
Keywords: lithium ion battery, Li-rich Mn based, cathode materials, hydrothermal, ionic liquid
Citation: Xiang Y, Jiang Y, Liu S, Wu J, Liu Z, Zhu L, Xiong L, He Z and Wu X (2020) Improved Electrochemical Performance of 0.5Li2MnO3·0.5LiNi0.5Mn0.5O2 Cathode Materials for Lithium Ion Batteries Synthesized by Ionic-Liquid-Assisted Hydrothermal Method. Front. Chem. 8:729. doi: 10.3389/fchem.2020.00729
Received: 26 May 2020; Accepted: 14 July 2020;
Published: 23 November 2020.
Edited by:
Cheng Zhong, Tianjin University, ChinaReviewed by:
Yan-Bing He, Tsinghua University, ChinaShiyou Zheng, University of Shanghai for Science and Technology, China
Copyright © 2020 Xiang, Jiang, Liu, Wu, Liu, Zhu, Xiong, He and Wu. This is an open-access article distributed under the terms of the Creative Commons Attribution License (CC BY). The use, distribution or reproduction in other forums is permitted, provided the original author(s) and the copyright owner(s) are credited and that the original publication in this journal is cited, in accordance with accepted academic practice. No use, distribution or reproduction is permitted which does not comply with these terms.
*Correspondence: Xianwen Wu, wxwcsu2011@163.com