Next Article in Journal
Novel Designated Ownership Transfer with Grouping Proof
Next Article in Special Issue
Research on the Structure and Control Strategy of a Novel Power Electronic Transformer for AC/DC Hybrid Distribution Network
Previous Article in Journal
Construction of the Uyghur Noun Morphological Re-Inflection Model Based on Hybrid Strategy
Previous Article in Special Issue
Voltage Ride through Control Strategy of Modular Multilevel Converter under Unbalanced Voltage Sag
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

Low-Voltage Solid-State DC Breaker for Fault Protection Applications in Isolated DC Microgrid Cluster

1
Department of Electrical and Electronic, University of The Ryukyu, 1 Senbaru, Nishihara, Okinawa 903-0213, Japan
2
Electrical Power and Machines Department, Zagazig University, Zagazig 44519, Egypt
3
Research Scientist at University of California, Riverside, 900 University Ave, Riverside, CA 92521, USA
*
Author to whom correspondence should be addressed.
Submission received: 2 January 2019 / Revised: 5 February 2019 / Accepted: 14 February 2019 / Published: 19 February 2019
(This article belongs to the Special Issue Emerging Power Electronics Technologies)

Abstract

:
Due to the interconnected scheme of multiple components, such as distributed generators, storage systems, and loads through converters to a common bus in DC microgrids, the possibility of fault occurrence is increasing significantly. Meanwhile, due to the huge and rapid increase of short-circuit currents, the development of a small- and large-scale DC system requires a reliable and fast protection system to ensure fault clearance and maintain safety for the rest of the system. Thus, fault protection has been focused on as one of the most critical issues in a direct current network. The application of traditional circuit-breakers for DC fault protection has the drawback of slow operation, which requires a high rating power equipment. Recently, the high speed and excellent performance capabilities of semiconductor breakers have attracted a lot of attention and been considered as an optimal solution for fast DC fault interruption. In this study, a bidirectional Insulated-Gate Bipolar Transistor (IGBT) semiconductor breaker, suitable for the fault protection of low-voltage DC networks, is proposed. The operating characteristics of this breaker are based on changes in the circuit current and terminal voltage of IGBTs. It detects the abrupt change of the terminal voltage as an abnormal condition and isolates the faulted branch in a short time to prevent the operation disturbance in the healthy part of the network. Therefore, for the entire protection of a typical 400V DC-microgrid cluster, breakers need to be integrated and examined in each branch and the interconnected lines. The proposed protection method in this study is examined in a Simulink®/MATLAB environment to analyze and assess its operation.

1. Introduction

A stand-alone DC microgrid is an independent, controllable, small-scale electrical system in the presence of Distributed Generators (DGs), controllable and non-controllable loads, power electronic components, and protective devices [1]. With the rapid development and integration of renewable energy resources, a novel alternative is required to ensure stable operation under different operation conditions. Based on the literatures, high- and low-voltage DC systems are recognized as an efficient method for power transmission and distribution. Since Edison’s time, the DC system has been implemented for energy supply purposes, but due to the lack of standards and technologies, AC system have been leading the DC network. Whereas the emerging of new power electronics and distributed energy resource technologies have made it easier to interconnect power components and build a multi-terminal DC system. However, DC short-circuit protection is still considered to be one of the major challenges for DC network applications in terms of small- and large-scale power transmission and distribution [2].
A large and growing body of literature has relied on low-voltage DC breakers in terms of a DC network or microgrid protection. More recently, in [3], a protection scheme for the hybrid AC/DC low-voltage distribution system based on transient stability analysis, backed by radial distribution system simulation and verification, has been proposed.
In [4], a mechanical DC breaker for real-time application is discussed. This study aims to propose a simulation mechanism for a DC breaker mechanical design at the simulation phase. This study formulates the components of a DC breaker (such as a high-speed vacuum interrupter, injection circuit, surge arrester, and residual switch) to evaluate the interruption of the DC fault in real-time.
In [5], an optimized method was hired to calibrate the DC circuit breaker with the help of an active injection circuit. This study took an optimized approach to enhance the DC circuit breaker’s performance according to its local fault current in a critical situation. The PSCAD® platform was used to evaluate the effectiveness of the proposed algorithm which could guarantee that the di/dt was within a safe limit during an interruption.
In [6], a framework was exposed based on a mathematical morphology approach to detect and protect a DC distribution network. This study characterized fault at a low-voltage distribution network, which focused on the DC short-circuit fault with low impedance, and a high impedance fault with arc concepts. The proposed filter-based approach is known as a cost-effective solution, in which there is no need for a communication link between relays or between a relay and its components.
In [7], a protection and control scheme for DC multi-microgrid configuration was proposed. This study tried to come up with an integrated solution in terms of simultaneous protection and control. The effectiveness of the study was evaluated through an experimental microcontroller circuit.
In a small-scale DC system, the distributed renewable generators, storage system, and loads can interface with the common bus through DC-converters, and prevent multiple energy conversion steps to deliver the most efficient and sustainable energy supply for power demands. Compared to AC, the DC power system does not have synchronization, reactive power, harmonics, skin effect, high heat-loss, and low-efficiency problems [8,9]. Also, there is no need for inverters to integrate DC power generators, storage devices, and DC loads with the direct current system. They can be integrated by highly efficient DC–DC converters to prevent large amounts of energy loss and system complexity. In addition, in any small-scale isolated microgrid, the total power generation capacity should be more than the maximum existing load to completely supply the load in any condition. Conversely, the output of renewable resources, especially the fluctuation of PV generators and wind turbines, depend on environmental conditions that result in power-supply instability. Thus, providing stable power by renewable generators is the main challenge when producing consistent electrical networks. Consequently, renewable generators need to be combined with energy storage systems to solve instability problems. Additionally, PV modules and the related power electronic converters as a small-scale DC system impact on the system’s operation in any short-circuit situation [10]. Also, converters can lose their controllability to retain the bus voltage within acceptable values. Due to the low DC impedance and rapid increase of the fault current, the DC network needs a high-speed protection system, which has significantly different requirements compared to an AC fault protection system. Fault area isolation from the rest of a DC grid would provide safety for the operation of non-faulted areas [11,12]. Furthermore, the application of traditional low-voltage (LV) AC protection solutions for a DC microgrid has the drawback of slow operation, resulting in the requirement for electrical components with a higher capacity (which cause a high initial cost and take up more space) [13]. Besides, battery banks or capacitors would feed the short-circuit current, resulting in a lot of thermal and mechanical stress on the system’s components [14]. To overcome this challenge in direct current systems, a high-speed protection system with an appropriate circuit breaker (CB) is a known exigence [15]. Due to the absence of mechanical components, contact erosion, having a long lifetime and high-speed operation (tens of microseconds ( μ s)), the semiconductor breakers are considered as a potential solution to overcome these barriers in a DC system [16,17].
In this study, we analyse a short-circuit protection scheme based on semiconductor technologies. For the protection of the entire network, an ideal two-way semiconductor Solid State Circuit Breaker(SSCB), based on IGBT and a control system are used to detect the fault current, and we isolated it in any part of the system within a short time. The rest of the paper is organized as follows: Section 2 deals with the structure of the proposed DC microgrid schemes and components design. The DC fault characteristics and effects are explained in Section 3. In Section 4 and Section 5, different fault-detection methods and the proposed methodology are introduced. The results and discussion are presented in Section 6 and Section 7. Finally, the study is concluded with the main findings and contributions in Section 8.

2. Simplified DC Microgrid Description and System Parameters

The configuration of the proposed small-scale multi-terminal low-voltage DC system with three small interconnected areas is shown in Figure 1. The breakers which connect the buses must open during the fault condition in any part of the interconnected lines. In each area, PV panels, loads, and the storage system, as the main components, were connected through the converters and breakers. the PV boost converter used a Maximum Power Point-Tracking-Incremental Conductance (MPPT-IC) Algorithm to track the maximum power point and deliver the maximum available power of the PV [18,19]. The feedback PI controller was used to regulate the output voltage of the boost rectifier. Also, batteries were equipped with a DC–DC bidirectional converter to provide two-way power flow. They charged by using the surplus power generation of PV and discharging over the night and cloudy periods. The main components of the system are listed in Table 1. In this configuration, power can be shared among the neighboring areas based on the voltage deviation of each local area. We also specified some representative locations where faults ( F 1 F 3 ) could occur in the system to evaluate the proposed protection system. Due to the effects of line impedance on the voltage drop, fault current, and fault interruption time, we considered it as a constant value. In a multi-terminal network, a consideration of CB at both ends of the line and interconnected buses are essential to prevent complete blackout by downstream short-circuit faults. Recently, the SSCB has been recognized by a key enabling technology for the DC distribution system and had the ability to interrupt the circuits under a full load within μ s. The regional short-circuit interruption can be perfectly obtained by integrating the CB with the related controller throughout the system [20]. The relevant electrical circuits and controllers of the converters with battery and solar panels are depicted in Figure 2, Figure 3 and Figure 4. In Figure 4, the difference of the bus voltage ( V b u s ) and the reference value (desired bus voltage) was computed by the synchronous measurement of the bus voltage, and the mismatch converged to the desired value through two feedback PI controllers and the proper operation of the bidirectional converter.

3. DC Fault Characteristics and Effects

Generally, two typical electrical faults (line-to-line and line-to-ground) can occur in a DC electrical system. In most cases, a short circuit is happening in the line-to-ground fault because of the easy connection between the line to the ground by any natural event or unintentional action. Comparatively, the line-to-line fault impedance is lower than the line-to-ground short-circuit condition, which causes a huge fault current during line-to-line faults. The impedance of line-to-ground faults can be either as a low or high-impedance depending on the type of the grounding system. Also, the types of grounding, characteristics of the distribution line, and system components have a direct effect on the voltage sag and the value of the fault current [14]. During any DC short-circuit accident, the resistance of the fault path can converge to its minimum value, and the fault current can increase to a peak value in a short time.
In this study, three typical DC short circuits were applied at three different points, as depicted in Figure 1. When faults occur, the current which flows through the related branch diverges from the normal value. Usually, five types of protection devices, such as mechanical breakers (Molded-Case Circuit Breakers (MCCB) and Miniature Circuit-Breakers (MCB)), fuses, SSCB, and the hybrid SSCB have been used for DC fault interruptions. However, their operation speed is different, which can range from a few ( μ s) for SSCB and about tens of milliseconds (ms) for mechanical breakers [21]. On the other hand, the maximum allowable time for the fault interruption can be decided based on how much the fault can withstand the capability of the system components. Fast short-circuit detection and segregation are necessary for system recovery and the reduction of electrical stresses on converters and the system components. For the proper selection of the protection device, the functionality, operation speed, time coordination, and controllability considerations are essential to deal with fast fault interruption and arc extinguishing. The design of a protection system needs to abide by the following characteristics [22]:
  • Operating speed;
  • Selectivity;
  • Reliability;
  • Reactivity;
  • Strength.

4. Methods Used for Fault Diagnosis

The most basic requirements of the circuit breakers are [23]:
  • Smaller arcing: For any type of circuit breaker, electric arcing should be suppressed and decreased to prolong the lifetime of the CB itself and also ensure tripping of the faulted circuit;
  • Completely controllable: The connecting and disconnecting of CB needs to be completely controllable, either by automatic mechanical tripping or digital controllers;
  • Operating speed: CBs for DC fault interruption are required to have an interrupting capability of fault currents with high speed to avoid huge short-circuit currents and destruction of the components;
  • Operational loss: The efficiency of CB should be appropriate for the normal operation of the system.
Different techniques and methodologies have been used for fault detection and isolation purposes in the electrical system. Some of the fault protection strategies are described as follows:

4.1. Non-Unit Protection Scheme

This method works based on the natural characteristics of the DC current and its first and second derivatives under the fault transients to assess the short-circuit impedance for specification and types of faults. This protection strategy is fast enough to interrupt the fault current and maintain the safety for the rest of the system. Too much communication delay can also be reduced by regional measurement of the system parameters. On the other hand, the implementation of many local components causes system complexity and needs high accuracy and initial costs [24].

4.2. Differential Protection Methodology

In advanced multi-terminal DC microgrids, the extension of short-circuit protection units is essential to ensure the safety of the whole system. In this method, it is obtained by the installation of local measurement and communication devices. Also, by computing the unknown parameters of the DC distribution line in short-circuit situations, as well as using communication links among protection components and SSCB, it is able to present fast fault protection (around 10 μ s) [25]. A reliable communication system needs to be implemented and interconnected with the local data among the terminals of the protective components synchronously. Additionally, the possibility of failure in data exchange and the interconnection delays is increased, resulting in low operation speed. Also, because of the mandatory emergency protection system, the system size and initial cost will also be increased [26].

4.3. Apparent Resistance

In this method, the current and voltage of each circuit branch are measured continuously to find the apparent resistance of the related branch. Consequently, the result is compared with the predefined threshold values (that will be within or outside of the positive and negative thresholds). When it is beyond the threshold value, the related MCB or SSCB goes into a fault current limitation condition to protect the circuit. The apparent resistance margin is adjusted to one-third of its rated value [27].

4.4. DC Fault Diagnosis and Protection Using CPU

This protection strategy works based on the change of current in each zone to identify and interrupt the fault branch. In a ring bus type or multi-terminal low-voltage DC system, the current of each small branch is measured and sent to the Digital Signal Processing Unit (DSPU) for further processing. For prevention of any error and delay, an accurate communication link is essential to transfer the measured data from each of the local devices to DSPU and the related breakers. Furthermore, in a short-circuit situation, the main valve of the semiconductor switches (IGB, MOSFET, etc.) in the converters will be closed and may not feed the fault current. Instead, the free-wheeling diode of the converter will provide a free-wheeling path to bypass the huge current which is generated by the discharge of distribution-line parameters. Thus, to maintain the safety for the converters, an auxiliary breaker is essential to interrupt the short-circuit current while the capacitor is discharging.

4.5. DC Fault Detection Based on Voltage Prediction

This fault protection strategy was developed based on the use of local measurements and the characteristics of the system parameter. This method does not require any kind of communication system, and works based on the deviation of the actual and predicted voltage. The deviation value depends on the location and type of the short circuit. In fault situations, a big gap between the actual and expected parameters will happen. Thus, a protection system design framework and a mathematical model was created for fast fault detection and isolation. Here, the faults are detected and isolated by using voltage data which is provided at the line side of the protective devices. Additionally, the Fault Current Limiter (FCL) method is also implemented for temporary fault circumstances. Although the fault-current limiting devices can efficiently limit a huge DC current and comparatively provide a low-cost protection system, it causes a longer detection time and interruption of the fault current [28].

5. Semiconductor Breakers and Operation Principle of the Proposed Method

Different types of Mechanical Circuit Breakers (MCB) and short-circuit termination strategies have been implemented for DC fault-protection purposes. Whereas, due to the rapid increase of DC fault currents and a low operation speed (hundreds of ms) of MCBs, it requires distribution line and associated power electronics devices with higher capacity and size to sustain such a high current. Comparatively, SSCB-based protection methods can provide high-speed protection (few μ s) schemes to prevent the high initial cost and occupation of large spaces [29]. The SSCBs are embedded into two useful major categories in protection system devices: (i) semiconductor current limiters, and (ii) semiconductor breakers [30]. The SSCBs consist of semiconductor switches (IGBT, MOSFET, etc.). Due to the absence of moving mechanical parts, the SSCB has a longer lifespan than MCB [31]. Among different types of semiconductor switches, the IGBT is a good choice for low-voltage protection purposes because of its operation speed, ruggedness, commercial availability, and low power requirement to run the gate drive. For reliability, the different circuit needs to be combined with SSCB, which are mentioned as follows:
  • Resistor, Capacitor, and Diode (RCD) Snubber Circuit:
    The main components of the RCD circuit are the resistor, capacitor, and diode. The resistor is connected in series to prevent high inrush current while the breaker is connecting, and the shunt capacitor suppresses the voltage jump during the disconnection of SSCB. Additionally, the anti-parallel diode circuit bypasses the high transient current, which generates when the breaker interrupts the circuit;
  • Metal Oxide Varistor (MOV):
    The MOV has the sustainability of frequent huge ripple currents and temporary high energy. Also, because of the variable resistance characteristics of MOV, it is used to protect electrical circuits under a surge voltage situation. The MOV makes a short circuit in high voltage conditions and its resistance is increased when the voltage decreases, meaning that the current-dependent equipment of the system will remain safe from the sudden voltage surge;
  • Freewheeling Diode:
    Normally, the snubber diode is not an overvoltage protective device, but helps to prevent circuit damage by providing an emergency path for high energy of the stray components when an abrupt voltage spike is happening in an electrical circuit by a sudden change of supply current or fault conditions.
Due to the capability of obtaining fast-fault interruption, SSCB can meet protection requirements for the DC-microgrid. A DC system has a unique challenge like DC short-circuit identification, appropriate grounding systems, and current limiting challenges. Due to a divergence in DC short-circuit current values, traditional protection devices will face challenges in reactivity and operating speed. Therefore, developing an appropriate protection strategy is quite important to expand the DC electrical system.
In this study, line-to-ground faults ( F 1 , F 2 , and F 3 ) were applied to evaluate the operation of the proposed protection system. Furthermore, the proposed protection system worked based on the current-rise technique of the fault current. For specification and detection of the fault situations, we defined the a threshold current in this strategy to identify the fault area easily. As shown in Figure 5, during the normal condition of the DC microgrid, the output of the control system for the circuit breaker was one and the circuit was prolonged to its normal operation. As soon as the control system sensed a divergence in the current of the circuit, the output signal changed to zero and the circuit breaker was disconnected to separate the faulted branch. Additionally, during the operation of SSCB, because of the abrupt interruption of the fault current, a large over-voltage would occur. Consequently, although the voltage rating of the semiconductor devices has recently improved, it still does not have high-voltage blocking capabilities, but will damage the breakers and other components in the system. Thus, multiple semiconductors need to be connected to improve the high-voltage blocking capability of the breaker. It will enlarge the components’ size and initial costs. Therefore, to provide safety for the components and prevent system enlargement, an over-voltage limiting circuit (parallel MOV) was integrated with the breaker to limit the rise in voltage and dissipate the high energy as heat. Also, for reliable operation and long life of the switches, accurate synchronization of gate controls and snubbing of stray energy was required. Therefore, Figure 5 shows the connection of two IGBT circuit breakers with anti-parallel diodes and its related operational controller. Additionally, when a short circuit is happening in any branch of the typical multi-terminal DC microgrid, a huge current will pass through the snubber diodes circuit, which causes an over-current on the system. Here, in this SSCB, and in a normal situation, the current will flow through the IGBTs, whereas in a short-circuit situation, the SSCB will be interrupted to reduce the current to zero. During the fault conditions, the protection system of the related area should pass the following steps:
  • Sensing the variation of the common bus voltage and converter current;
  • Sending an operation command for related protection devices operation;
  • Blocking the CB and turning off the power unit converters in the fault branch;
  • Waiting for a few ms after Step 3 to ensure that the current of faulted feeder decays turns to zero;
  • Opening the related breaker and de-energizing the faulted branch;
  • Re-energizing the fault branch by closing the CBs and the converter.
The faults in Figure 1 are considered an ideal line-to-ground short circuit with zero resistance, and the result of the proposed protection strategy is depicted in Figure 6, Figure 7, Figure 8, Figure 9, Figure 10 and Figure 11. In each case, when a DC fault occurs, the fault current increases rapidly, whereas the SSCB interrupts it before it reaches the peak value. Still, a high current which passes through the breaker and a large amount of energy will be accumulated in a surge arrestor, which can be calculated by Equations (1) and (2) [32]. Additionally, the surge voltage across the breaker is limited to the clamping voltage of the MOV, and it is assumed V d c + V m a r g i n :
I = I O V m a r g i n L t
The total dissipated energy as heat by the surge arrestor is given by the equation below:
W R = ( V V m a r g i n + 1 ) 1 2 L I O 2
Where in these equations, V is the normal voltage of the system, and I O and W R represent the amplitude of the fault current and energy absorbed in the surge arrestor, respectively. Commonly, the amount of V m a r g i n is much smaller than V to suppress the voltage rise across the SSCB. Therefore, the amount of W R in MOV is a large quantity. In a freewheeling diode SSCB’s types, the purpose of the diode is to provide a path for large currents and reverse voltage impulses. The amount of energy bypassed by a snubber diode is given by the equation below:
W R = 1 2 L I O 2
Consequently, as shown in Equations (2) and (3), the energy absorbed in the MOV type is more than the energy bypassed by the snubber diode type. Furthermore, in order to decrease the fault current quickly while the breaker is disconnecting, the voltage capacity of the SSCB should be more than V b u s [33].

6. Simulation Results

As mentioned in previous sections, during the fault condition, the converter’s current reaches such a high value within a short time to cause the breakage of converters. Therefore, the application of SSCB is necessary to maintain the system’s safety. Different simulation scenarios, such as load side and distribution feeder faults, are carried out to verify the performance of the proposed topology. In the first scenario at t = 1.5 s, a pole-to-ground fault ( F 1 ) is initiated at the load side in area A. In the second scenario, a pole-to-ground fault is applied in area B at 1.7 s. The third DC fault is applied on the feeder, which connects area A and B at time 2 s. In regard to the main objective for this study, which is fast fault interruption, the operational safety of the rest of the system is maintained and keeps the system components in an acceptable range. As shown in Figure 6, Figure 7, Figure 8, Figure 9, Figure 10 and Figure 11, during the three fault scenarios, the current in each case starts to increase exponentially, and is only limited by the DC line resistance ( R L i n e ). When the fault current reaches the positive or negative threshold values, the breaker interrupts the fault current within a few μ s to prevent system failure and maintain a stable power for the load demands. Additionally, Figure 10 shows the DC bus voltage during F 2 , where as soon as the bus voltage decreases more than the threshold value, the nearest CB to the fault in area B suddenly disconnects the fault branch and the bus voltage returns to its normal value. The simulation results for the current, voltage waveforms, and State of Charge (SoC) of the battery during the fault conditions are depicted in the following figures.

7. Discussion and Analysis

The three-case simulations verification shows the amount of voltage drop along the distributed line, protection, and isolation of the fault branch which occurred in different areas at different times. The normal voltage drop along the feeder is 12 V, which is 3 % of the rated voltage, as depicted in Figure 10. Also, when F 2 occurs, the DC bus voltage is dropped to 235 V and returns to the normal situation after the fault interruption. In Figure 7, when F 1 is happening in area A, due to the isolation of the load branch, the rate of charge in this area increases more rapidly than the other parts. Meanwhile, the fault currents ( I F 1 , I F 2 ) reach its maximum values, 60 A and 72 A, respectively. After the disconnection of short circuits, the accumulated energy is attracted by MOV, and the fault current decays to 0 A within 15 μ s until the fault is removed from the system and is reconnected within 8 μ s, as shown in Figure 8 and Figure 11. During this time, the current rise is limited to a certain value, and after the fault interruption the current flow increases to reach the neighboring areas, as shown in Figure 6 and Figure 9. Furthermore, during F 3 at 2 s, the current flow jumped to a high value from B and C to the faulted point, but the breakers which were connecting B and C acted abruptly at both sides and disconnected the fault. However, the high conduction loss and cost of the semiconductor breakers technology was considered as the main obstacle to wide application. However, there is a comparison among the cheap MCB with a low operation speed and fast semiconductor breakers with high conduction losses for protection application. Additionally, there are some current fluctuations at the end of the simulation in Figure 6, Figure 9, and Figure 11. At this time, the solar radiation is decreased rapidly in three areas and the PV outputs are too low to support the load, which causes high current fluctuation among the areas to supply the connected loads and share the power. The simulation results have shown that the SSCB safely turned off, and the rest of the system continued to operate normally. Also, the freewheeling diodes started conducting, while the currents reached values that were not affordable by converters.

8. Conclusions

This paper presented an isolated DC microgrid cluster within an innovative approach of using IGBT-based SSCB protection devices. At the start, the most recent literature and findings in the context of low-voltage solid-state DC beakers were reviewed. Then, existing challenges, along with DC fault behavior analysis with different protection strategies, were systematically investigated. Consequently, a viable, cost-effective solution using IGBT and SSCB compared to the traditional AC fault protection was exposed. The proposed scheme effectiveness was evaluated by applying three short circuits at different time-frames, in which the sensed current and voltage deviation at the voltage terminal of IGBTs and branch currents demonstrated improved behavior. Besides, when the current deviation went beyond the permitted the threshold, the associated SSCB simultaneously took action by receiving an interruption command from the controller. The simulation results show that the proposed short-circuit interruption strategy is fast enough to maintain DC microgrid safety, along with stabilization and operational performance improvement.

Author Contributions

M.A.Y. has proposed the DC fault protection and built the simulation model for the DC microgrid and SSCB. All the authors analyzed and discussed the results and made the corrections.

Acknowledgments

This study is a part of the research efforts, which is technically and financially supported by University of the Ryukyus and JICA. The authors would like to express their cordial thanks to the University of the Ryukyus and JICA.

Conflicts of Interest

The authors declare no conflict of interest.

References

  1. Lotfi, P.; Bahramirad, K. State of the art in research on Microgrids: A review. IEEE Access 2015, 3, 890–925. [Google Scholar]
  2. Cuzner, R.M.; Venkataramanan, G. The Status of DC Micro-Grid Protection. In Proceedings of the 2008 IEEE Industry Applications Society Annual Meeting, Edmonton, AB, Canada, 5–9 October 2008. [Google Scholar]
  3. Noh, C.; Kim, C.; Gwon, G.; Khan, M.O.; Jamali, S.Z. Development of protective schemes for hybrid AC/DC low-voltage distribution system. Electr. Power Energy Syst. 2018, 105, 521–552. [Google Scholar] [CrossRef]
  4. Liu, S.; Liu, Z.; Chavez, J.D.; Popov, M. Mechanical DC circuit breaker model for real time simulations. Electr. Power Energy Syst. 2018, 107, 110–119. [Google Scholar] [CrossRef]
  5. Liu, L.; Liu, S.; Popov, M. Optimized algorithm of active injection circuit to calibrate DC circuit breaker. Electr. Power Energy Syst. 2018, 103, 369–376. [Google Scholar] [CrossRef]
  6. Oh, Y.; Kim, C.; Gwon, G.; Noh, C.; Bukhari, S.B.A.; Haider, R.; Gush, T. Fault detection scheme based on mathematical morphology in last mile radial low voltage DC distribution networks. Electr. Power Energy Syst. 2018, 106, 520–527. [Google Scholar] [CrossRef]
  7. Abdali, A.; Noroozian, R.; Mazlumi, K. Simultaneous control and protection schemes for DC multi microgrids systems. Electr. Power Energy Syst. 2018, 104, 230–245. [Google Scholar] [CrossRef]
  8. Estefana, P.; Andreu, J.; Grate, J.I.; de Alegra, I.M.; Ibarra, E. AC and DC technology in microgrids: A review. Renew. Sustain. Energy Rev. 2015, 43, 726–749. [Google Scholar]
  9. Sajadian, S.; Santos, E.C.D. RCD snubber circuit design for 5-level 4switch DC-AC converter. In Proceedings of the 40th Annual Conference of the IEEE Industrial Electronics Society, Dallas, TX, USA, 29 October–1 November 2014; pp. 4371–4377. [Google Scholar]
  10. Salonsson, D.; Soder, L.; Sannino, A. Protection of Low-Voltage DC Microgrids. IEEE Trans. Power Deliv. 2009, 24, 1045–1053. [Google Scholar] [CrossRef]
  11. Tang, L.; Ooi, B. Locating and isolating dc faults in multi-terminal dc systems. IEEE Trans. Power Deliv. 2007, 22, 1877–1884. [Google Scholar] [CrossRef]
  12. Baran, M.; Mahajan, N. Overcurrent protection on voltage-sourceconverter-based multiterminal DC distribution systems. IEEE Trans. Power Deliv. 2007, 22, 406–412. [Google Scholar] [CrossRef]
  13. Dragicevic, T.; Lu, X.; Vasquez, J.; Guerrero, J.M. DC microgrids—Part II: A review of power architectures, applications, and standardization issues. IEEE Trans. Power Electron. 2016, 5, 3528–3549. [Google Scholar] [CrossRef]
  14. Jae-Do, P.; Candelaria, J. Fault detection and isolation in low-voltage DC-bus microgrid system. IEEE Trans. Power Deliv. 2013, 28, 779–787. [Google Scholar]
  15. Elsayed, A.T.; Mohamed, A.A.; Mohammed, O.A. DC microgrids and distribution systems: An overview. Electr. Power Syst. Res. 2015, 119, 407–417. [Google Scholar] [CrossRef]
  16. Miao, Z.; Sabui, G.; Moradkhani, A.; Wang, J.; Shuai, Z.; Yin, X. A self-powered bidirectional DC solid state circuit breaker using two normally-on SiC JFETs. In Proceedings of the 2015 IEEE Energy Conversion Congress and Exposition, Montreal, QC, Canada, 20–24 September 2015. [Google Scholar]
  17. Gu, C.; Wheeler, P.; Castellazzi, A.; Watson, A.J.; Effah, F. Semiconductor Devices in Solid-State/Hybrid Circuit Breakers: Current Status and Future Trends. Energy 2017, 6, 495. [Google Scholar] [CrossRef]
  18. Jaw-Kuen, S.; Lee, M.; Wei, Y.; Chen, B. Circuit simulation for solar power maximum power point tracking with different buck-boost converter topologies. Energies 2014, 7, 5027–5046. [Google Scholar]
  19. Mobarrez, M.; Ghanbari, N.; Bhattacharya, S. Control Hardware-in-the-Loop Demonstration of a Building-Scale DC Microgrid Utilizing Distributed Control Algorithm. In Proceedings of the PES General Meeting, Portland, OR, USA, 5–9 August 2018. [Google Scholar]
  20. Kempkes, M.; Roth, I.; Gaudreau, M. Solid-State Circuit Breakers for Medium Voltage DC Power. In Proceedings of the 2011 IEEE Electric Ship Technologies Symposium, Alexandria, VA, USA, 10–13 April 2011. [Google Scholar]
  21. Lin, H.; Antsaklis, P.J. Stability and stabilization of switched linear system: A survey of recent results. IEEE Trans. Autom. Control 2009, 54, 308–322. [Google Scholar] [CrossRef]
  22. Munasib, S.; Balda, J.C. Short-Circuit Protection for Low-Voltage DC Microgrids Based on Solid-State Circuit Breakers. In Proceedings of the IEEE International Symposium on Power Electronics for Distributed Generation Systems, Vancouver, BC, Canada, 27–30 June 2016; pp. 1–7. [Google Scholar]
  23. Cairoli, P.; Kondratiev, I.; Dougal, R. Coordinated control of the bus tie switches and power supply converters for fault protection in DC microgrids. IEEE Trans. Power Electron. 2013, 28, 2037–2047. [Google Scholar] [CrossRef]
  24. Meghwani, A.; Srivastava, S.C.; Chakrabarti, S. A Non-unit Protection Scheme for DC Microgrid Based on Local Measurements. IEEE Trans. Power Deliv. 2017, 32, 172–181. [Google Scholar] [CrossRef]
  25. Fletcher, S.; Norman, P.; Fong, K.; Galloway, S.J.; Burt, G.M. High-speed differential protection for smart DC distribution systems. IEEE Trans. Smart Grid 2014, 5, 2610–2617. [Google Scholar] [CrossRef]
  26. Dhar, S.; Patnaik, R.K.; Dash, P.K. Fault Detection and Location of Photovoltaic Based DC Microgrid Using Differential Protection Strategy. IEEE Trans. Smart Grid 2015, 99, 4303–4312. [Google Scholar] [CrossRef]
  27. Cairoli, P.; Dougal, R.A.; Lentijo, K. Coordination between supply power converters and contactors for fault protection in multi-terminal MVDC distribution systems. Electr. Ship Technol. Symp. 2013, 499, 22–24. [Google Scholar]
  28. Corzine, K.A.; Ashton, R.W. A new Z-source DC circuit breaker. IEEE Trans. Power Electron. 2012, 27, 2796–2804. [Google Scholar] [CrossRef]
  29. Wang, D.; Emhemed, A.; Norman, P.; Burt, G. Evaluation of existing DC protection solutions on an active LVDC distribution network under different fault conditions. CIRED 2017, 2017, 890–925. [Google Scholar] [CrossRef]
  30. Madingou, G.; Zarghami, M.; Vaziri, M. Fault detection and isolation in a DC microgrid using a central processing unit. In Proceedings of the IEEE Power & Energy Society Innovative Smart Grid Technologies Conference (ISGT), Washington, DC, USA, 17–20 February 2015; pp. 1–5. [Google Scholar]
  31. Shen, Z.; Miao, Z.; Roshandeh, A. Solid state circuit breakers for DC microgrids: Current status and future trends. In Proceedings of the 2015 IEEE First International Conference on DC Microgrids (ICDCM), Atlanta, GA, USA, 7–10 June 2015. [Google Scholar]
  32. Muriuki, J.; Nyakoe, G.; Muriithi, C.; Ngoo, L. Novel Modeling of a Fast DC Breaker for a VSC-HVDC Transmission System Protection. Electr. Electron. Syst. 2017, 6, 4. [Google Scholar] [CrossRef]
  33. Urciuoli, D.; Veliadis, V. Demonstration of a 600-V, 60-A, bidirectional silicon carbide solid-state circuit breaker. In Proceedings of the 2011 Twenty-Sixth Annual IEEE Applied Power Electronics Conference and Exposition (APEC), Fort Worth, TX, USA, 6–11 March 2011. [Google Scholar]
Figure 1. The single-line diagram of a DC microgrid cluster and fault locations.
Figure 1. The single-line diagram of a DC microgrid cluster and fault locations.
Applsci 09 00723 g001
Figure 2. Circuit diagram of the boost converter and the related feedback PI controller.
Figure 2. Circuit diagram of the boost converter and the related feedback PI controller.
Applsci 09 00723 g002
Figure 3. Circuit diagram of bidirectional converter for the battery and PI controller.
Figure 3. Circuit diagram of bidirectional converter for the battery and PI controller.
Applsci 09 00723 g003
Figure 4. Feedback PI control diagram of the battery’s bidirectional converter.
Figure 4. Feedback PI control diagram of the battery’s bidirectional converter.
Applsci 09 00723 g004
Figure 5. SSCB circuit diagram and the fault current control system.
Figure 5. SSCB circuit diagram and the fault current control system.
Applsci 09 00723 g005
Figure 6. The current flow from area A to B during F 1 .
Figure 6. The current flow from area A to B during F 1 .
Applsci 09 00723 g006
Figure 7. State of charge of batteries in three areas during F 1 .
Figure 7. State of charge of batteries in three areas during F 1 .
Applsci 09 00723 g007
Figure 8. Fault current during DC short circuit F 1 and F 2 .
Figure 8. Fault current during DC short circuit F 1 and F 2 .
Applsci 09 00723 g008
Figure 9. Current flow from B to A during F 2 .
Figure 9. Current flow from B to A during F 2 .
Applsci 09 00723 g009
Figure 10. DC bus voltage at the source and load side during F 2 .
Figure 10. DC bus voltage at the source and load side during F 2 .
Applsci 09 00723 g010
Figure 11. Current flow from B to C during F 3 .
Figure 11. Current flow from B to C during F 3 .
Applsci 09 00723 g011
Table 1. System parameter and components.
Table 1. System parameter and components.
ParameterValueSymbol
Max P P V 1 20.5 kW P P V 1
Max P P V 2 31 kW P P V 2
Max P P V 3 41 kW P P V 3
DC L o a d 1 15 kW L 1
DC L o a d 2 23 kW L 2
DC L o a d 3 34 kW L 3
Battery45 (3 × 15) kWhB
DC bus voltage400 V V b u s
Feeder length 1 . 5 km
Switching Frequency5 kHzF
Line Resistance0.14 Ω /kmR
Line Inductance0.24 mH/kmL

Share and Cite

MDPI and ACS Style

Yaqobi, M.A.; Matayoshi, H.; Danish, M.S.S.; Lotfy, M.E.; Howlader, A.M.; Tomonobu, S. Low-Voltage Solid-State DC Breaker for Fault Protection Applications in Isolated DC Microgrid Cluster. Appl. Sci. 2019, 9, 723. https://0-doi-org.brum.beds.ac.uk/10.3390/app9040723

AMA Style

Yaqobi MA, Matayoshi H, Danish MSS, Lotfy ME, Howlader AM, Tomonobu S. Low-Voltage Solid-State DC Breaker for Fault Protection Applications in Isolated DC Microgrid Cluster. Applied Sciences. 2019; 9(4):723. https://0-doi-org.brum.beds.ac.uk/10.3390/app9040723

Chicago/Turabian Style

Yaqobi, Mohammad Aman, Hidehito Matayoshi, Mir Sayed Shah Danish, Mohammed Elsayed Lotfy, Abdul Motin Howlader, and Senjyu Tomonobu. 2019. "Low-Voltage Solid-State DC Breaker for Fault Protection Applications in Isolated DC Microgrid Cluster" Applied Sciences 9, no. 4: 723. https://0-doi-org.brum.beds.ac.uk/10.3390/app9040723

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Metrics

Back to TopTop