Next Article in Journal
Decomposition of Used Tyre Rubber by Pyrolysis: Enhancement of the Physical Properties of the Liquid Fraction Using a Hydrogen Stream
Next Article in Special Issue
Impact of Modified Spacer on Flow Pattern in Narrow Spacer-Filled Channels for Spiral-Wound Membrane Modules
Previous Article in Journal
A Simple Method to Evaluate Adaptation Measures for Urban Heat Island
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

Performance of Reverse Osmosis Membranes in the Treatment of Flue-Gas Desulfurization (FGD) Wastewaters

1
Institute on Membrane Technology, ITM-CNR, c/o University of Calabria, via P. Bucci, 17/C, I-87036 Rende, Italy
2
Department of Environmental & Chemical Engineering, University of Calabria, Via P. Bucci, 44/A, I-87036 Rende, Italy
*
Authors to whom correspondence should be addressed.
Environments 2018, 5(6), 71; https://doi.org/10.3390/environments5060071
Submission received: 28 May 2018 / Revised: 16 June 2018 / Accepted: 17 June 2018 / Published: 19 June 2018
(This article belongs to the Special Issue Environmental Applications of Membrane Technology)

Abstract

:
Reverse osmosis (RO) was studied to reduce salinity of flue gas desulfurization (FGD) wastewaters after softening with Na2CO3·H2O and ultrafiltration (UF). Two commercial thin film composite polyamide RO membranes (SWC-2540 and ESPA-2540, from Hydranautics) in spiral-wound configuration were tested and their performance in terms of salinity reduction as well as permeate flux, fouling index and water recovery was evaluated. Experimental runs were performed according to the feed and bleed configuration in selected operating conditions. For the SWC-2540 membrane experiments were also performed in total recycle configuration in order to evaluate the effect of operating pressure on permeate flux and quality. Experimental results indicated that the SWC-2540 membrane showed a better performance in the rejection of ions: Mg2+ ions were completely rejected, while the rejection towards monovalent ions such as Na+ was of about 95.5%. The ESPA-2540 membrane showed rejections towards Ca2+ and Mg2+ higher than 86.5% whilst the observed rejection towards Na+ was of 80%. For the SWC-2540 membrane an increased rejection for Ca2+ and Na+ ions was observed by increasing the operating pressure in the range 16-50 bar. Mg2+ ions were totally rejected independently by the operating pressure.

Graphical Abstract

1. Introduction

The combustion of coal in power generation facilities produces solid waste, such as bottom and fly ash, and flue gas that is emitted to the atmosphere. The sulfur dioxide reduction from the exhausted flue gas of fossil fuel thermoelectric power plants is accomplished through wet scrubber technologies according to a process known as flue gas desulfurization (FGD). Wet scrubbers typically remove more than 90% of sulfur dioxide, compared to dry scrubbers, which remove only 80%. These processes generate a polluted wastewater with an extremely complex composition depending on coal source, type of scrubber, makeup water quality, gypsum-dewatering system used and operational conditions.
Typically, FGD wastewaters contain significantly high concentration of chloride, sulfate, nitrate, calcium and magnesium and trace-levels of heavy metals, such as Hg(II), Pb(II), Cd(II), Mn(II) and Ni(II). Total dissolved solids (TDS) are in the range 4000–50,000 mg/L, while suspended solids range from 1.4% to 17% [1].
Discharge of FGD wastewaters without sufficient treatment pose serious environmental issues because of its detrimental impact on human health and ecological system. In this scenario, according to the European Directive 2000/60/CE, the use of regenerated water takes a key role in conferring utmost protection to water. In addition, the use of regenerated wastewater for irrigation purposes offer very interesting perspectives in terms of both environmental and economic impact.
Biological processes [2,3,4], flocculation [5], adsorption [6], constructed wetland [7], evaporation [8], chemical precipitation [9] and electrocoagulation [10] are typically used to remove heavy metal ions, nitrate or soluble organic contaminants from FGD wastewater. These methods do not meet standard regulations, especially for the high salinity of the FGD wastewaters. In addition, they are significantly constrained by process complexity, large investment, high maintenance cost, operating difficulties and other shortcomings and limitations. Therefore, advanced treatments based on the selective removal of various trace contaminants from such a complex matrix, are one of the biggest challenges for thermal power plants.
Membrane technologies are a high potential option in order to attempt the complete depuration of FGD wastewaters due to their advantages over conventional separations systems such as compact modular nature, high efficiency and moderate investment and maintenance costs. These processes are becoming increasingly used in the recent years in the purification of water and groundwater, in replacement of many conventional separation processes, as well as in the reclamation of several wastewater streams. In particular, pressure-driven membrane operations such as microfiltration (MF), ultrafiltration (UF), nanofiltration (NF) and reverse osmosis (RO) have been increasingly implemented in the recent years in the purification of groundwater and surface water as well as for decontamination of wastewater streams of very diverse sources [11,12]. Among pressure-driven membrane operations, RO represents a valid approach for treating wastewater with high conductivity. It is generally used to remove water pollutants, such as phosphorus, organic matter as well as in desalination processes, in order to remove, for example, Na+ and Cl [13].
Few studies have been reported until now on the use of membrane operations in the treatment of FGD wastewaters. For instance, polyvinylidene fluoride (PVDF) microfiltration (MF) membranes in hollow fiber configuration have been used to remove Hg after chemical precipitation from FGD wastewaters providing a simple, reliable, long-term and cost economic solution for the reduction of mercury compounds in these wastewaters [14]. An integrated process based on the use of nanofiltration (NF) and membrane distillation (MD) processes for practical application in FGD wastewater treatment has been also recently investigated by Jia and Wang [15]. The whole system exhibited nearly complete salt rejection and over 92% water reclamation ratio.
This work was aimed at evaluating the performance of commercial reverse osmosis (RO) membranes, in terms of salinity reduction as well as permeate flux, fouling index and water recovery, in the treatment of softened and ultrafiltered flue-gas desulfurization (FGD) wastewaters.

2. Materials and Methods

2.1. Softening and Pre-Treatment Processes of FGD Wastewaters

FGD wastewaters were provided by IER (Industrial Enel Research, Brindisi, Italy). Before use, they were submitted to a chemical pre-treatment in order to remove the amount of inorganic compounds (in particular calcium and magnesium) that can cause scaling issue during RO treatment, reducing membrane performance. In particular, FGD wastewaters were softened with Na2CO3·H2O (>97%, Carlo Erba Reagenti, Milan, Italy) in order to reduce the quantity of calcium and magnesium. A preliminary set of experiments was performed to select the appropriate amount of alkalizing agents in order to achieve maximum removal efficiencies. At this purpose, the effect of Na2CO3·H2O/Ca2+ molar ratio on the removal of calcium was studied in a fixed volume of FGD wastewaters at a temperature of 25 °C. The solutions were incubated for 1 h to let the majority of the solids particles settle out and then ultrafiltered before acidification with H2SO4 up to pH 6.5.
Ultrafiltration (UF) was performed by using a laboratory unit (Verind SpA, Milan, Italy) equipped with a polyethersulfone hollow fiber membrane module supplied by Microdyn-Nadir (Wiesbaden, Germany) having a nominal molecular weight cut-off (MWCO) of 500 kDa and an effective membrane area of 0.25 m2. UF was operated according to a feed-and-bleed configuration (the permeate is removed from the system and replaced by an equal volume of feed solution while the retentate stream is recycled back to the feed reservoir) at a transmembrane pressure (TMP) of 0.5 bar, an axial feed flow rate (Qf) of 500 L/h and a temperature (T) of 25 ± 2 °C, up to a recovery factor (RF) of 97.5%.

2.2. Treatment of Permeate UF by RO: Experimental Set-Up and Membranes

RO experimental runs were performed by using a laboratory plant supplied by Matrix Desalination Inc. (Fort Lauderdale, FL, USA). The equipment consists of a feed tank with a capacity of 10 L, a stainless steel housing for 2.4 × 21 inches spiral-wound membrane module, a high pressure pump, two pressure gauges (0–100 bar) for the control of the inlet and outlet pressures and a backpressure valve. A coiling cool, fed with tap water, was used to maintain the feed temperature constant.
Two commercial spiral wounds RO membranes in composite polyamide namely SWC-2540 and ESPA-2540 from Hydranautics (Hydranautics Corporation, Oceanside, CA, USA) were studied. Properties of the selected membranes, are summarized in Table 1. Experimental runs were performed according to the feed and bleed configuration in selected operating conditions (TMP 26 bar, Qf 204 L/h, T 20 °C for the SWC membrane and TMP 18 bar, Qf 220 L/h, T 20 °C for the ESPA 2540 membrane) up to a RF of 50%, corresponding to a weight reduction factor (WRF) of 2. The ESPA-2540 membrane was tested at lower TMP values, according to the manufacturer’s data sheet.
For the SWC-2540 membrane experiments were also performed in total recycle configuration (in which concentrate and permeate streams were both recycled back to the feed tank) in order to evaluate the effect of TMP on the permeate flux and quality of the obtained permeate. Experiments were performed in the range of TMP values between 16 and 50 bar (at T of 25 °C and Qf of 240 L/h), so as to generate a steady-state flux (about 40 min for each TMP value). When flux values were stable, permeate samples were collected to determine the rejection coefficients.
After each experiment, membranes were rinsed with water and then cleaned with an acid solution (Ultraclean WO 0.05%, pH 4) at 40 °C, for 60 min, in total recycle configuration. At the end of each cleaning procedure membrane modules were rinsed with distilled water for 20 min and the water permeability was measured again.

2.3. Permeate Fluxes, Hydraulic Permeability, Fouling Index and Cleaning Efficiency

During the filtration experiments the permeate flux was continuously monitored by measuring the permeate weight collected in a certain time according to the following equation:
J p = W p A   t
where Jp is the permeate flux (kg/m2h), Wp the permeate weight (kg) at time t (h) and A the membrane surface area (m2).
The hydraulic permeability (Wp) of each membrane was determined by the slope of the straight line obtained plotting the water flux values, measured in fixed conditions of temperature (25 °C), versus the applied TMP.
The fouling index (FI), expressed as a percentage drop in the water permeability, was estimated by measuring the water permeability before and after the treatment of FGD wastewaters, according to the following equation:
F I = ( 1 W p 1 W p 0 ) × 100
where Wp0 and Wp1 are the pure water permeability before and after FGD wastewaters treatment.
The cleaning efficiency (CE) was evaluated according to the following equation:
C E = ( W p 2 W p 0 ) × 100
where Wp2 is the water permeability measured after the chemical cleaning.

2.4. Analytical Methods

pH was measured by an Orion Expandable ion analyzer EA 920 pH meter (Allometrics, Inc., Baton Rouge, LA, USA) with automatic temperature compensation. Electrical conductivity (ED) and total dissolved solids (TDS) were measured using a digital conductivity meter (HI 2300 Microprocessor Conductivity, Hanna Instruments, Woonsocket, RI, USA). Concentration of the main cations (Ca2+, Mg2+ and Na+) was determined by using a high-resolution continuum source atomic absorption spectrometer (HR-CSAAS, ContrAA700, Analytik Jena AG, Jena, Germany), with a high intensity Xe short arc lamp as continuum source. Samples and standards were fed to the flame by an Injection Module (SFS6), which allowed washing or continuous aspiration of the carrier solution. They were appropriately diluted (300 times for Mg and Ca, 3000 times for Na). Subsequently they were acidified with 1% HCl. Method parameters (i.e., fuel flow and burner height) obtained by the flame automatic optimization procedure for the determination of Ca2+ (N2O/acetylene flame) and Na+ or Mg2+ (air-acetylene flame) were applied, the absorbance measurements being performed using the spectral lines for Ca at 422.67 nm, for Na at 588.99 and for Mg at 285.21 nm.
The removal efficiency for each analyzed component was determined during membrane processes and quantified as percentage rejection (R) of a particular component:
  R = ( 1 C p C f ) · 100
where cf and cp are the component concentrations in the feed and permeate, respectively.

3. Results and Discussion

3.1. Pre-Treatment Processes

The appropriate dose of Na2CO3·H2O for an efficient softening process was investigated experimentally. Sodium carbonate promotes the removal of Ca2+ ions through reactive precipitation as CaCO3. Therefore, the proper Na2CO3 addition was determined with respect to the Ca2+ ion concentration in the FGD wastewaters to be treated. The obtained results (Figure 1) prove that Ca2+ and Mg2+ removal efficiency increased by growing the coagulant dosage until Na2CO3·H2O/Ca2+ molar ratio between 2.27 and 3.18, then a plateau is reached. In particular, in this range the removal of Ca2+ achieved up to 90%, whilst the removal of Mg2+, at the same coagulant dosage, was of about 30%. The pH of the FGD wastewaters increased from 9.2 to 10.6 in the range of investigated Na2CO3·H2O/Ca2+ molar ratio due to the increased release of OH ions in the solution.
Ayoub et al. [20] investigated the removal of inorganic compounds (including calcium and magnesium) in seawater using Na2CO3 as alkalizing agents and obtained similar results. In particular, the removal efficiencies recorded were of 90 ± 2.5% for Ca2+ and 15 ± 4.55% for Mg2+. A similar Ca2+ removal efficiency (higher than 90%) was observed also by Zheng et al. [21] during the treatment of textile and dyeing wastewaters using NaOH. Based on these experimental results, an average Na2CO3·H2O/Ca2+ molar ratio of 2.6 was chosen for performing the softening.
Before RO, softened FGD wastewaters were preliminary submitted to a UF process. In the selected operating conditions steady-state UF permeate fluxes of about 480 kg/m2h were obtained. The composition of FGD wastewaters before and after the chemical and the UF treatments is reported in Table 2. As expected, in the optimized Na2CO3·H2O/Ca2+ molar ratio conditions a higher removal of Mg2+ and Ca2+ was obtained whilst, the removal of other analyzed compounds was lower (in the range 11–27%). The UF process, allowed to remove more than 60% of TOC, while the content of inorganic compounds and TDS remained unchanged in agreement with the MWCO of the selected UF membrane.

3.2. RO of Pre-Treated FGD Wastewaters

Figure 2 shows the time evolution of permeate flux for both RO membranes in the treatment of the softened and ultrafiltered FGD wastewater, in the selected operating conditions. Despite different operating TMP values, RO membranes showed similar initial permeate fluxes values (of about 14 kg/m2h). The permeate flux declined rapidly in the first 30 min; then the rate of flux decline became slower and a pseudo-steady state flux of 2.3 kg/m2h and 1.9 kg/m2h for the ESPA and SWC membranes respectively, was reached. This behavior has to be attributed to the increase of the osmotic pressure of feed solution due to the high salt rejection of the selected membranes, and to the concentration polarization and membrane fouling phenomena. This leads to a severe driving force decrease and, consequently, to a flux decline [22]. In particular, the observed flux decline of selected membranes was in the range of 84–86%.
A similar permeate flux decline was observed by Vourch et al. [23] in the treatment of dairy industry wastewaters for water reuse, with a RO spiral wound membrane (TFC HR SW 2540) in thin film composite, having a NaCl rejection of the same order (99.5%).
Dolar et al. [24] obtained a permeate flux decline of about 72% during processing of pre-treated landfill leachate with a RO (XLE) membrane from Dow/Filmtec (Midland, MI, USA).
A street correlation between the concentration of feed solution and permeate flux decline was reported by Tang et al. [25] in the processing of semiconductor wastewaters with a RO ESPA membrane. They obtained a reduction of permeate flux of 10% at a concentration of feed solution of 10 ppm of perfluorooctane sulphonate (PFOS) and of about 60% at 500 ppm of PFOS. Authors attributed the flux decline with the entrapment of PFOS molecules in the polyamide layer and their accumulation on the membrane surfaces.
Table 3 shows the fouling index for the selected membranes based on their water permeability before and after the pre-treated FGD wastewaters filtration. According to the obtained values, the ESPA membrane showed a lower fouling index (FI, 28.8%) in comparison with the SWC membrane (FI, 35.3%). This behavior could be attributed to the different morphology (surface roughness) and contact angles of selected membranes (Table 1). As reported in literature, membranes with smooth and hydrophilic surfaces (as the ESPA) presented less fouling tendency than those with rough and hydrophobic surfaces (as the SWC) [26].
After cleaning with water, the water permeability of both membranes was lower than 10% when compared to the initial one. After chemical cleaning, a complete recovery of the initial water permeability was observed for the SWC-2540 membrane and of about 92% for the ESPA 2540 membrane. The low fouling index measured for both membranes and the almost complete recovery of RO membranes performance could be attributed to the pre-treatment processes (softening, precipitation and ultrafiltration) that limited inorganic scaling and the possible deposition of inorganic substances on membrane surface or inside the membrane pores [26].
The selected membranes were also compared in terms of permeate quality and removal of salt compounds. The chemical composition of permeate and retentate fractions produced with both RO membranes, at a WRF 2, is reported in Table 4.
The electrical conductivity rejection for ESPA-2540 and SWC-2540 membranes, were of about 85.7% and 93.2%, respectively (Figure 3). The TDS rejection of the SWC-2540 membrane was relatively higher (93%) if compared with the ESPA-2540 membrane (87%). In addition, the SWC-2540 membrane showed a better performance in the rejection of ions. Mg2+ ions were completely rejected by the SWC-2540 membrane (R of 100%), while the rejection towards monovalent ions such as Na+ was lower (R of about 95.5%). The ESPA-2540 membrane showed rejections towards Ca2+ and Mg2+ higher than 86.5%; on the other hand, the observed rejection towards Na+ was of 80%. Considering that divalent ions are larger than monovalent ions, the main mechanism of ion rejection by RO membranes is size exclusion [27]. However, the charges of ions and membranes employed cannot be neglected since they also interact each other electrostatically. At the pH of FGD wastewaters (6.5) both membranes are negatively charged [18,19]. Therefore, electrostatic attraction forces between the negatively charged membrane surface and specific ions can contribute to the retention mechanism.
In Table 5 and Table 6 the mass balance of the RO process for both investigated membranes is reported. The balance is referred to RO experimental runs in which starting from 18 L of pre-treated FGD wastewaters, 9 L of permeate and 9 L of retentate were obtained. It can be noted that for both RO membranes, the main ions are mainly concentrated in the retentate streams; on the other hand, the amount in the permeate is lower than 10%. The balance is complete, indicating that no interaction ions-membranes, or adsorption of ions on the membranes surface, occurs during the process.
According to the obtained results, the SWC-2540 membrane exhibited the highest removal efficiency for all measured parameters. Therefore, the quality of the produced permeate was higher if compared with the permeate produced by ESPA-2540 membrane. The SWC-2540 permeate presented an electrical conductivity lower than 2 mS/cm; it resulted completely depleted of bivalent ions such as Mg2+, with a low amount of total dissolved solids (TDS) (<1 g/L) and Ca2+.

3.3. Experiments in Total Recycle Mode

For the SWC-2540 membrane experiments were also performed according to the total recycle configuration in order to evaluate the effect of TMP on the permeate flux and the removal efficiency of salt compounds. Figure 4 shows the time evolution of the permeate flux at different TMP values (increased in the range 16–50 bar) and fixed values of temperature and feed flowrate (25 °C and 240 L/h, respectively). An increase of initial and steady-state permeate fluxes from 0.86 kg/m2h to 16.8 kg/m2h and from 0.61 kg/m2h to 10.4 kg/m2h, respectively, was observed by increasing the operating pressure in the range of investigated values.
Mohammadi et al. [28] reported a linear increase of permeate flux with pressure in the treatment of seawater with a polyamide FT30 RO membrane. A linear trend between permeate flux and pressure was also observed by Mondal and Wickramasinghe [29] in the treatment of oily wastewaters with a BW 30 membrane (FilmTec Corporation, Minneapolis, MN, USA) in aromatic polyamide with a NaCl rejection of 99.4%.
A different behavior was reported by Liu et al. [30] in the treatment of textile effluents for water reuse with the same membrane (BW30). In this case, a decrease of permeate fluxes by increasing the operating pressure, was observed.
From Figure 4 it is also possible to note that working at high pressure values (higher than 20 bar) there is an increase of the permeate flux decline by increasing the operating time. As previously discussed, this behavior could be attributed to membrane fouling and concentration polarization phenomena. Particularly, working at high pressure, concentration polarisation is known to be the main factor that contributes to the increasing salt concentration at the membrane surface hence leading to particle deposition and an increasing of scaling [31].
In Figure 5 the effect of TMP on the rejection towards main ions and other analyzed compounds, is showed. It can be noted that the rejection of Mg2+ was not affected by TMP: indeed, the rejection was of 100% independently by the applied pressure. Adversely, an increase of rejection by increasing the operating pressure was observed for Ca2+ and Na+. In particular, the rejection for Ca2+ and Na+ increased from 32.3% and 82.2% at TMP of 16 bar to 78% and 98% at TMP of 50 bar, respectively. A similar trend was observed for TDS rejection. Similar results, in terms of TDS rejection, were observed by Nataraj et al. [32] in the removal of dye and salts from simulated wastewaters with a TFC polyamide RO membrane in spiral-wound configuration.
The increase of the rejections by increasing the TMP could be attributed to the increase of solvent flux at higher pressure, resulting in the decreasing of salts concentration and ions in the permeate. On the other hand, during the RO treatment more components (ions and salts) are transported from the bulk solution towards the membrane surface as permeate flux increases, which enhance concentration polarization and consequently the faster flux decline (from the initial to the steady-state values) at the increasing of TMP.

4. Conclusions

Reverse osmosis (RO) was studied to reduce the saline content of softened and ultrafiltered flue gas desulfurization (FGD) wastewaters. Commercial spiral-wound RO membranes (named SWC and ESPA) were tested on laboratory scale and compared for their performance in terms of productivity, salt rejections, fouling index and cleaning efficiency.
The SWC membrane was effective in reducing more than 85% of Na+, Ca2+ and Mg2+ ions in selected operating conditions with low fouling index and higher cleaning efficiency in comparison to the ESPA membrane. Retention values for Na+ and Ca2+ ions increased by increasing the operating pressure, whilst Mg2+ ions were totally rejected independently by the transmembrane pressure.
Further investigations will be devoted to the combination of RO with membrane distillation in order to process the RO brine for the production of high purity water (which can be reused in thermal power plant) and salts (when membrane distillation is operated as membrane distillation/crystallization). The integrated system might allow exploiting the added value of RO brine, extracting water and crystals, thus approaching zero-liquid discharge strategy.

Author Contributions

E.D. supervised the technical activities and the paper writing. A.C. and F.M. conceived and designed the experiments (softening and membrane treatment of FGD wastewaters). Lab scale experiments of softening and membrane processing of FGD wastewaters were performed by C.C. She was also involved in the analytical characterization of feed, pretreated, permeate and retentate samples with technical contribution of P.A. All Authors contributed to the interpretation and discussion of experimental results.

Funding

This work was performed within the Project “Materials Technologies for performance improvement of Cooling Systems in Power Plants” (MATChING) which received funding from the European Union’s Horizon 2020 research and innovation program under the grant agreement number 686031.

Conflicts of Interest

The authors declare no conflict of interest.

References

  1. USEPA. Steam Electric Power Generating Point Source Category: Final Detailed Study Report. EPA 821-R-09-08; 2009. Available online: https://www.epa.gov/sites/production/files/2015-06/documents/steam-electric_detailed_study_report_2009.pdf (accessed on 26 April 2018).
  2. Pickett, T.; Sonstegard, J.; Bonkoski, B. Using biology to treat selenium. Power Eng. 2008, 110, 140–145. [Google Scholar]
  3. Wei, C.; He, W.J.; Wei, L.; Ma, J.; Li, C.Y. The performance and microbial communities of biodegradation-electron transfer with sulfur metabolism integrated process for flue gas desulfurization wastewater treatment. Bioprocess. Biosyst. Eng. 2017, 40, 1543–1553. [Google Scholar] [CrossRef] [PubMed]
  4. Zhang, L.; Lin, X.J.; Wang, J.T.; Jiang, F.; Wei, L.; Chen, G.H.; Hao, X.D. Effects of lead and mercury on sulfate-reducing bacterial activity in a biological process for flue gas desulfurization wastewater treatment. Sci. Rep. 2016, 6, 30455. [Google Scholar] [CrossRef] [PubMed]
  5. Wu, Z.B.; Ni, W.M.; Guan, B.H. Application of chitosan as flocculant for coprecipitation of Mn(II) and suspended solids from dual-alkali FGD regenerating process. J. Hazard. Mater. 2008, 152, 757–764. [Google Scholar] [CrossRef] [PubMed]
  6. Huang, Y.H.; Peddi, P.K.; Tang, C.L.; Zeng, H.; Teng, X.J. Hybrid zero-valent iron process for removing heavy metals and nitrate from flue-gas-desulfurization wastewater. Sep. Purif. Technol. 2013, 118, 690–698. [Google Scholar] [CrossRef]
  7. Sundberg-Jones, S.E.; Hassan, S.M. Macrophyte sorption and bioconcentration of elements in a pilot constructed wetland for flue gas desulfurization wastewater treatment. Water Air Soil Pollut. 2007, 183, 187–200. [Google Scholar] [CrossRef]
  8. Ma, S.C.; Chai, J.; Chen, G.D.; Yu, W.J.; Zhu, S.J. Research on desulfurization wastewater evaporation: Present and future perspectives. Renew. Sustain. Energy Rev. 2016, 58, 1143–1151. [Google Scholar]
  9. Yu, J.; Lu, J.; Kang, Y. Removal of sulfate from wet FGD wastewater by co-precipitation with calcium hydroxide and sodium aluminate. Water Sci. Technol. 2018, 77, 1336–1345. [Google Scholar] [CrossRef] [PubMed]
  10. Liu, S.N.; Ye, X.K.; He, K.; Chen, Y.C.; Hu, Y.Y. Simultaneous removal of Ni(II) and fluoride from a real flue gas desulfurization wastewater by electrocoagulation using Fe/C/Al electrode. J. Water Reuse Desalin. 2017, 7, 288–297. [Google Scholar] [CrossRef]
  11. López, J.; Coello, M.D.; Quiroga, J.M. Comparative studies of reverse osmosis membranes for wastewater reclamation. Desalination 2006, 191, 137–147. [Google Scholar] [CrossRef]
  12. Van der Bruggen, B.; Vandecasteele, C. Removal of pollutants from surface water and groundwater by nanofiltration: Overview of possible applications in the drinking water industry. Environ. Pollut. 2003, 122, 435–445. [Google Scholar] [CrossRef]
  13. Malaeb, L.; Ayoub, G.M. Reverse osmosis technology for water treatment: State of the art review. Desalination 2011, 267, 1–8. [Google Scholar] [CrossRef]
  14. Liu, C.; Farooq, K.; Doll, B.; Venkatadri, R. Economical and reliable mercury reduction in refinery and power plant discharge wastewater with robust microfiltration membrane technology. Desalin. Water Treat. 2013, 51, 4980–4986. [Google Scholar] [CrossRef]
  15. Jia, F.; Wang, J. Treatment of flue gas desulfurization wastewater with near-zero liquid discharge by nanofiltration-membrane distillation process. Sep. Sci. Technol. 2018, 53, 146–153. [Google Scholar] [CrossRef]
  16. Li, Q.; Song, J.; Yu, H.; Li, Z.K.; Pan, X.H.; Yang, B. Investigating the microstructures and surface features of seawater RO membranes and the dependencies of fouling resistance performances. Desalination 2014, 352, 109–117. [Google Scholar] [CrossRef]
  17. Dražević, E.; Košutić, K.; Fingler, S.; Drevenkar, V. Removal of pesticides from the water and their adsorption on the reverse osmosis membranes of defined porous structure. Desalin. Water Treat. 2011, 30, 161–170. [Google Scholar] [CrossRef]
  18. Lee, S.; Lee, E.; Elimelech, M.; Hong, S. Membrane characterization by dynamic hysteresis: Measurements, mechanisms, and implications for membrane fouling. J. Membr. Sci. 2011, 366, 17–24. [Google Scholar] [CrossRef]
  19. Ishida, K.P.; Bold, R.; Phipps, D.W. Identification and Evaluation of Unique Chemicals for Optimum Membrane Compatibility and Improved Cleaning Efficiency; Technical Report April; Orange County Water District: Fountain Valley, CA, USA, 2005. [Google Scholar]
  20. Ayoub, G.M.; Zayyar, R.M.; Al-Hindi, M. Precipitation softening: A pre-treatment process for seawater desalination. Environ. Sci. Pollut. Res. 2014, 21, 2876–2887. [Google Scholar] [CrossRef] [PubMed]
  21. Zheng, L.; Wang, X.; Wang, X. Reuse of reverse osmosis concentrate in textile and dyeing industry by combined process of persulfate oxidation and lime-soda softening. J. Clean. Prod. 2015, 108, 525–533. [Google Scholar] [CrossRef]
  22. Teixeira, A.R.S.; Santos, J.L.C.; Crespo, J.C. Sustainable membrane-based process for valorization of cork boiling wastewaters. Sep. Purif. Technol. 2009, 66, 35–44. [Google Scholar] [CrossRef]
  23. Vourch, M.; Balannec, B.; Chaufer, B.; Dorange, G. Treatment of dairy industry wastewater by reverse osmosis for water reuse. Desalination 2008, 219, 190–202. [Google Scholar] [CrossRef] [Green Version]
  24. Dolar, D.; Košutić, K.; Strmecky, T. Hybrid processes for treatment of landfill leachate: Coagulation/UF/NF-RO and adsorption/UF/NF-RO. Sep. Purif. Technol. 2016, 168, 39–46. [Google Scholar] [CrossRef]
  25. Tang, C.Y.; Fu, Q.S.; Robertson, A.P.; Criddle, C.; Leckie, J.O. Use of reverse osmosis to remove perfluorooctane sulfonate (PFOS) from semiconductor wastewater. Environ. Sci. Technol. 2006, 40, 7343–7349. [Google Scholar] [CrossRef] [PubMed]
  26. Jiang, S.; Li, Y.; Ladewig, B.P. A review of reverse osmosis membrane fouling and control strategies. Sci. Total Environ. 2017, 595, 567–583. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  27. Sert, G.; Bunani, S.; Yörükoğlu, E.; Kabay, N.; Egemen, Ö.; Arda, M.; Yüksel, M. Performances of some NF and RO membranes for desalination of MBR treated wastewater. J. Water Proc. Eng. 2017, 16, 193–198. [Google Scholar] [CrossRef]
  28. Mohammadi, T.; Moghadam, M.K.; Madaeni, S.S. Hydrodynamic factors affecting flux and fouling during reverse osmosis of seawater. Desalination 2002, 151, 239–245. [Google Scholar] [CrossRef]
  29. Mondal, S.; Wickramasinghe, S.R. Produced water treatment by nanofiltration and reverse osmosis membranes. J. Membr. Sci. 2008, 322, 162–170. [Google Scholar] [CrossRef]
  30. Liu, M.; Lü, Z.; Chen, Z.; Yu, S.; Gao, C. Comparison of reverse osmosis and nanofiltration membranes in the treatment of biologically treated textile effluent for water reuse. Desalination 2011, 281, 372–378. [Google Scholar] [CrossRef]
  31. Goh, P.S.; Lau, W.J.; Othman, M.H.D.; Ismail, A.F. Membrane fouling in desalination and its mitigation strategies. Desalination 2018, 425, 130–155. [Google Scholar] [CrossRef]
  32. Nataraj, S.K.; Hosamani, K.M.; Aminabhavi, T.M. Nanofiltration and reverse osmosis thin film composite membrane module for the removal of dye and salts from the simulated mixtures. Desalination 2009, 249, 12–17. [Google Scholar] [CrossRef]
Figure 1. Effect of Na2CO3·H2O/Calcium molar ratio on salt removal and pH.
Figure 1. Effect of Na2CO3·H2O/Calcium molar ratio on salt removal and pH.
Environments 05 00071 g001
Figure 2. Reverse osmosis (RO) of pre-treated flue gas desulfurization (FGD) wastewaters with selected membranes. Time course of permeate flux. (T, 20 °C; Qf, 220 L/h; recovery factor (RF), 50%).
Figure 2. Reverse osmosis (RO) of pre-treated flue gas desulfurization (FGD) wastewaters with selected membranes. Time course of permeate flux. (T, 20 °C; Qf, 220 L/h; recovery factor (RF), 50%).
Environments 05 00071 g002
Figure 3. Rejection of RO membranes towards ions, electrical conductivity (EC) and total dissolved solids (TDS).
Figure 3. Rejection of RO membranes towards ions, electrical conductivity (EC) and total dissolved solids (TDS).
Environments 05 00071 g003
Figure 4. RO of pre-treated FGD wastewaters with SWC-2540 membrane. Permeate flux as function of transmembrane pressure (TMP) (T, 25 °C; Qf, 240 L/h).
Figure 4. RO of pre-treated FGD wastewaters with SWC-2540 membrane. Permeate flux as function of transmembrane pressure (TMP) (T, 25 °C; Qf, 240 L/h).
Environments 05 00071 g004
Figure 5. Rejection of SWC membrane towards ions, electrical conductivity (EC) and total dissolved solids (TDS) at different TMP values.
Figure 5. Rejection of SWC membrane towards ions, electrical conductivity (EC) and total dissolved solids (TDS) at different TMP values.
Environments 05 00071 g005
Table 1. Characteristics of spiral-wound membrane modules.
Table 1. Characteristics of spiral-wound membrane modules.
Membrane TypeSWC-2540ESPA-2540
ManufacturerHydranauticsHydranautics
Membrane materialComposite polyamideComposite polyamide
Salt rejection (%)99.4 (minimum 99)99.4 (minimum 98)
pH operating range2–112–10
Max. operating temperature (°C)4545
Max. operating pressure (bar)6921
Membrane surface area (m2) 2.342.34
Water permeability (kg/m2hbar)1.77 a5.90 a
Contact angle (°)58.9 ± 1.2 b34.0 ± 2.00 c
Zeta potential (mV)−21.2 at pH 7 d−26.0 at pH 7.0 e
a our data; b data from [16]; c data from [17]; d data from [18]; e data from [19].
Table 2. Composition of flue gas desulfurization (FGD) wastewaters before and after pre-treatment processes (EC, electrical conductivity; TDS, total dissolved solids; TC, total carbon; TOC, total organic carbon; IC, inorganic carbon).
Table 2. Composition of flue gas desulfurization (FGD) wastewaters before and after pre-treatment processes (EC, electrical conductivity; TDS, total dissolved solids; TC, total carbon; TOC, total organic carbon; IC, inorganic carbon).
SampleCa2+
(ppm)
Mg2+
(ppm)
Na+
(g/L)
EC
(mS/cm)
TDS
(g/L)
TC
(mg/L)
TOC
(mg/L)
IC
(mg/L)
FGD wastewater 384.4 ± 4.8289.4 ± 2.67.2 ± 0.633.6 ± 2.116.9 ± 0.6 ---
After softening83.8 ± 0.5174.7 ± 1.26.4 ± 0.825.08 ± 1.612.46 ± 1.890.96 ± 0.9190.12 ± 0.900.57 ± 0.05
After ultrafiltration 82.0 ± 1.6 171.8 ± 3.46.3 ± 0.1225.8 ± 0.512.5 ± 0.282.98 ± 0.8333.80 ± 0.3449.18 ± 0.49
Table 3. Hydraulic permeability measurement and fouling index of reverse osmosis (RO) membranes (Wp0, initial water permeability; Wp1, after the treatment with FGD wastewaters; Wp2, after cleaning with water at 30 °C; Wp3, after acid cleaning at pH 4).
Table 3. Hydraulic permeability measurement and fouling index of reverse osmosis (RO) membranes (Wp0, initial water permeability; Wp1, after the treatment with FGD wastewaters; Wp2, after cleaning with water at 30 °C; Wp3, after acid cleaning at pH 4).
ParameterMembrane Type
SWC-2540ESPA-2540
Wp0 (kg/m2hbar)1.75.9
Wp1 (kg/m2hbar)1.14.2
Wp2 (kg/m2hbar)1.65.2
Wp3 (kg/m2hbar)1.75.4
Fouling index (FI) (%) 35.328.8
Cleaning efficiency (CE) (%)100.092.0
Table 4. Chemical composition of FGD wastewaters before and after RO treatment.
Table 4. Chemical composition of FGD wastewaters before and after RO treatment.
Membrane TypeSampleCa2+
(ppm)
Mg2+
(ppm)
Na+
(g/L)
EC
(mS/cm)
TDS
(g/L)
SWC-2540Feed83.5 ± 1.7178.4 ± 3.56.4 ± 0.126.1 ± 0.5212.6 ± 0.25
Permeate11.0 ± 0.2n.d.0.29 ± 0.011.76 ± 0.030.87 ± 0.01
Retentate159.2 ± 3.4362.2 ± 7.812.52 ± 0.2649.3 ± 1.024.6 ± 0.5
ESPA-2540Feed52.1 ± 1.03196.2 ± 3.96.4 ± 0.125.1 ± 0.513.9 ± 0.3
Permeate6.75 ± 0.136.8 ± 0.131.25 ± 0.023.6 ± 0.21.8 ± 0.04
Retentate98.6 ± 2.2383.6 ± 7.811.5 ± 0.2545.6 ± 2.322.8 ± 0.7
Table 5. Mass balance of the RO process for the SWC-2540 membrane.
Table 5. Mass balance of the RO process for the SWC-2540 membrane.
ParameterFeedPermeateRetentateBalance
Volume18 L9 L50.0%9 L50.0%100.0%
Ca2+1503 mg99.0 mg6.5%1432.8 mg95.3%101.8%
Mg2+3211.2 mg0 mg0.0%3259.8 g101.5%101.5%
Na+115.2 mg2.6 mg2.2%112.7 g97.8%100.0%
Table 6. Mass balance of the RO process for the ESPA-2540 membrane.
Table 6. Mass balance of the RO process for the ESPA-2540 membrane.
ParameterFeedPermeateRetentateBalance
Volume18 L9 L50.0%9 L50.0%100.0%
Ca2+937.8 mg60.7 mg6.5%887.4 mg94.6%101.1%
Mg2+3531.6 mg61.2 mg1.7%3452.4 g97.7%99.4%
Na+115.2 mg11.2 mg9.7%103.5 g89.9%99.6%

Share and Cite

MDPI and ACS Style

Conidi, C.; Macedonio, F.; Argurio, P.; Cassano, A.; Drioli, E. Performance of Reverse Osmosis Membranes in the Treatment of Flue-Gas Desulfurization (FGD) Wastewaters. Environments 2018, 5, 71. https://0-doi-org.brum.beds.ac.uk/10.3390/environments5060071

AMA Style

Conidi C, Macedonio F, Argurio P, Cassano A, Drioli E. Performance of Reverse Osmosis Membranes in the Treatment of Flue-Gas Desulfurization (FGD) Wastewaters. Environments. 2018; 5(6):71. https://0-doi-org.brum.beds.ac.uk/10.3390/environments5060071

Chicago/Turabian Style

Conidi, Carmela, Francesca Macedonio, Pietro Argurio, Alfredo Cassano, and Enrico Drioli. 2018. "Performance of Reverse Osmosis Membranes in the Treatment of Flue-Gas Desulfurization (FGD) Wastewaters" Environments 5, no. 6: 71. https://0-doi-org.brum.beds.ac.uk/10.3390/environments5060071

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Metrics

Back to TopTop