Next Article in Journal
Techno-Economic Analysis and Environmental Impact of Electric Buses
Previous Article in Journal
A Procedure to Estimate Air Conditioning Consumption of Urban Buses Related to Climate and Main Operational Characteristics
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

Conceptual Design Optimization of Autonomous Electric Buses in Public Transportation

1
TUMCREATE Limited, 1 Create Way, #10-02 CREATE Tower, Singapore 138602, Singapore
2
Institute of Automotive Technology, Technical University of Munich, Boltzmannstr. 15, 85748 Garching, Germany
*
Author to whom correspondence should be addressed.
World Electr. Veh. J. 2021, 12(1), 30; https://0-doi-org.brum.beds.ac.uk/10.3390/wevj12010030
Submission received: 25 January 2021 / Revised: 8 February 2021 / Accepted: 10 February 2021 / Published: 18 February 2021

Abstract

:
Autonomous electric buses (AEB) have widely been envisioned in future public transportation systems due to their large potential to improve service quality while reducing operational costs. The requirements and specifications for AEBs, however, remain uncertain and strongly depend on the use case. To enable the identification of the optimal vehicle specifications, this paper presents a holistic design optimization framework that explores the impacts of implementing different AEB concepts in a given set of routes/network. To develop the design optimization framework, first, a multi-objective, multi-criteria objective function is formulated by identifying the attributes of bus journeys that represent overall value to the stakeholders. Simulation models are then developed and implemented to evaluate the overall performance of the vehicle concepts. A genetic algorithm is used to find the concepts with the optimal trade-off between the overall value to the stakeholders and the total cost of ownership. A case study is presented of a single bus line in Singapore. The results show an improvement in the waiting time with the use of a smaller sized AEB with a capacity of 20 passengers. However, the costs and emissions increase due to the requirement of a larger fleet and the increase in daily distance traveled compared to a 94-passenger capacity AEB.

1. Introduction

Technological advances in electrification and automation are transforming the automotive industry as governments are seeking for sustainable public transportation solutions to improve transport efficiency, reduce traffic congestion, and minimize Greenhouse Gas (GHG) emissions. Following the electrification of urban buses to eliminate local emissions of nitrogen oxides and particulate matter, there has been a wide interest in automating urban city buses to promote a modal shift away from private car usage to ease traffic congestion [1,2].
Automation of public transit is expected to attract more users, as the service quality can be improved by decreasing the waiting and travel time of passengers [3] while reducing operational costs from the drivers’ remuneration. To improve the service quality, operators can increase the frequency of buses or operate vehicles of smaller sizes to increase bus frequencies while reducing operating costs of traveling empty. Various projects, such as the DART [4] in Singapore and HEAT [5] in Hamburg, Germany, are therefore investigating the use of autonomous electric minibuses to complement existing public transport.
Several original equipment manufacturers (OEMs) are also focusing on developing autonomous buses of smaller capacities between 10–60 passengers such as the concepts from NAVYA [6], Easy mile EZ-10 [7], GRT shuttle [8] and SCANIA NXT [9]. Buses of different sizes and configurations are therefore expected in the prospective product portfolios of bus OEMs.
In the pre-development phase of the automotive product development process, strategic decisions need to be made regarding the preliminary specifications of the vehicle. To minimize the development time, methods such as parametric modeling [10,11,12] and conceptual design optimization [13,14,15,16] are used to define the vehicle parameters in the early concept phase to find solutions that best meet the development objectives.
Vehicle concept optimization has been widely studied for the design of conventional, hybrid and electric passenger vehicle concepts [17]. Research has been conducted at different levels from the component level up to the entire vehicle concept. At the component level, the component type and size are optimized [18]. At the topology level, systems such as the powertrain [19,20] and cooling [21] are optimized, and at the vehicle concept level, the entire vehicle concept is optimized based on multi-criteria design objectives [15,16,22].
To optimize the overall vehicle concept, various studies have been conducted by Ziemann [23], Meurle [24], Weber [25], Wiedemann [14], and Schockenhoff [26] to identify the properties of vehicles that provide value to the user such as comfort, off-road performance, and top speed. The properties describe all the relevant aspects of the vehicle from the user’s perspective and allows for the formulation of an objective function. The vehicle concept is, therefore, optimized to maximize the benefit to the user.
Wiedemann [27] identifies and develops a method to optimize seven properties of range, cost efficiency, passenger comfort, design, everyday suitability, lateral dynamics, and longitudinal dynamics for the design of electric passenger vehicles. Various methods such as pattern search, design of experiments, and evolutionary algorithms are further investigated to calculate the optimal vehicle specifications.
Matz [15] further develops a method to optimize passenger electric vehicle concepts in a multi-modal transport network using the properties identified in [27]. A multi-objective optimization is implemented that finds concepts with the optimal trade-off between the value to the user and total cost of ownership (TCO). The model uses the NSGA-II genetic algorithm to find the set of Pareto optimal solutions.
Vehicle concept optimization methods represent the state-of-research in the development of conventional and electric passenger vehicles. However, such methods have not been widely applied in the development of buses. The majority of publications on electric buses study and compare the lifecycle costs and GHG emissions of Battery-Electric Buses against Diesel and Hybrid powertrains and discuss the potential of using alternative powertrain technologies [28,29,30]. Due to the high costs of the battery technology and charging infrastructure, other studies [31,32,33] investigate the influence of the battery size, charging method such as depot and opportunity charging, on costs and analyze the optimal vehicle and charging schedules [34,35].
A holistic design optimization of buses has not been conducted. Furthermore, the influence of the automation of buses on the vehicle concept design has also not been investigated in detail. Therefore, this paper presents a holistic design optimization framework to identify the optimal autonomous electric bus (AEB) concepts for a given set of routes/network. The properties of AEBs are first investigated to formulate the objective function for the optimization. A simulation framework is developed to enable the calculation and evaluation of AEB concepts in a public transport network. Finally, a case study is presented on a bus route in Singapore to compare the impacts of different vehicle sizes on the costs, emissions, and overall value to the stakeholders.

2. Methodology

The overall methodology of this paper consists of three main parts, as shown in Figure 1. First, the properties of AEBs are determined from the perspective of the users, bus operators, and government authorities. Next, an objective function is formulated by identifying value functions representing the correlation between the value to the stakeholders and the technical specification of the properties. Lastly, in the implementation step, simulation models are developed and implemented to evaluate different vehicle concepts in a public transport network.

2.1. Derivation of Properties

In the automotive development process, the overall system design requirements are described from the stakeholders’ perspective [25,36]. The requirements are structured into three levels [26] of properties, attributes, and technical specifications. The properties describe the overall qualities that the user perceives and comprises of attributes that are directly quantifiable by a technical specification such as top speed and acceleration time.
To derive the overall properties for the development of AEBs, first, a stakeholder and persona analysis is conducted to analyze the different bus users and their needs during various phases of the bus journey from arrival and boarding at the bus stop to traveling and alighting at the destination stop [37]. Subsequently, a functional assessment is carried out to identify the attributes of the bus journey that would influence the stakeholders’ preferences and satisfaction. Using a taxonomy approach, the attributes are categorized to form the properties. Nine property fields, shown in Table 1, are identified through the categorization of the attributes: service performance, accessibility, comfort, functionality, information, safety, longitudinal dynamics, environmental performance, and costs.
Two online surveys, a stated preference, and a pairwise-comparison of the properties were developed to find the stakeholders’ preferences towards the attributes and obtain the weighting factors for the properties. The surveys were disseminated by distributing QR-codes directly to bus passengers in Singapore, emails to bus operators, and social media platforms. A total of 225 responses were received and analyzed using the Analytic Hierarchy Process to calculate the weighting factors of the properties and attributes. The survey questionnaires and responses are described in detail in [37].

2.2. Formulation of the Objective Function

To conduct a holistic design optimization of AEBs, a multi-criteria objective function, y, is formulated using the derived properties. The objective function consists of two objectives shown in Equations (1) and (2). The first objective y(1) maximizes the property fulfillment and is calculated using the weighted (W) sum of the property value. The second objective y(2) minimizes the TCO, for a vector x that consists of the vehicle parameters. The weights for both the properties and attributes are obtained from the surveys analyzed in the preceding step [37].
y 1 = max ( f S e r v i c e P e r f o r m a n c e x * W S e r v i c e P e r f o r m a n c e + f A c c e s s i b i l i t y x * W A c c e s s i b i l i t y + f C o m f o r t x * W C o m f o r t + f F u n c t i o n a l i t y x * W F u n c t i o n a l i t y + f I n f o r m a t i o n x * W I n f o r m a t i o n + f S a f e t y x * W S a f e t y + f L o n g i t u d i n a l D y n a m i c s x * W L o n g i t u d i n a l D y n a m i c s + f E n v i r o n m e n t a l P e r f o r m a n c e x * W E n v i r o n m e n t a l P e r f o r m a n c e )
y 2 = min T o t a l C o s t s x
Each property is calculated by taking the weighted sum of its comprising attributes shown in Table 1. The attributes are evaluated using value functions that correlate how desirable the value of the technical specification is, in the view to the stakeholders on a scale of 1–10. The value functions are derived by benchmarking existing vehicles and analyzing vehicle standards and public transport satisfaction surveys. Figure 2 shows instances of the value functions used to quantify the attributes. A logistic function is used to represent the value functions rather than a linear correlation as proposed by Aigner [38], as the added value to the user reduces with increasing satisfaction. For example, for the attribute legroom, shown in Figure 2c, as the seat pitch increases, the value to the passenger increases exponentially up to a seat pitch of 750 mm. Any further increase in seat pitch does not provide additional satisfaction to the passenger. The curve, therefore, flattens out towards the end points.
However, for some attributes, the technical specification is not continuous and takes discrete values—for example, the attribute wheelchair zones in Figure 2f. The value function is modeled using a step function that represents value to the user in discrete steps based on the number of wheelchair zones in the vehicle.
To determine the optimization variables, a correlation matrix is used to qualitatively correlate the vehicle parameters listed in [39,40] with the identified attributes in Table 1, on a 3-point scale of strong, weak, and no correlation. The parameters with strong correlations are specified to be the optimization variables and are presented in Table 2 along with lower and upper bounds.

2.3. Implementation of Simulation Models

To evaluate the objective function in Equations (1) and (2), a simulation framework is developed to calculate the property fulfillment and the total costs. The model is implemented in MATLAB and solved using an optimization algorithm. As the objective function is non-linear, the Non-Dominated Sorting Genetic Algorithm (NSGA-II) [41] is used for the optimization.
Figure 3 shows the overall framework which consists of the implemented models. For a given set of routes, a vehicle concept is defined and created using a parametric packaging model according to the design parameters of the optimization. Next, the schedule for the derived concept is analyzed and through a route simulation the impacts on the passenger waiting time and vehicle occupancy levels are analyzed. A longitudinal dynamics simulation subsequently simulates the energy consumption of the concept. A vehicle assignment model then analyzes the vehicle concept’s impact on the fleet size, and total distance traveled to calculate the TCO and life cycle emissions accurately. The following sections of the methodology describe the implemented simulation models to evaluate the attributes in the objective function and perform the overall optimization.

2.3.1. Inputs

The required inputs to conduct the simulation consist of the route data, the driving cycle for the powertrain simulation, the charging method—depot charging or opportunity charging, and the corresponding charger power. The route data consists of the passengers’ hourly origin-destination matrix along the route, inter-stop distance and travel times between bus stops, and distance and time matrix between the depots and route termini.
For the routes analyzed in this work, the input data is obtained from the fare card dataset provided by Singapore’s Land Transport Authority. The data is parsed to obtain the route level origin-destination matrices of the passengers and inter-stop distance and travel times.

2.3.2. Package Calculation

At each iteration of the optimization, a vehicle package calculation is first conducted. The packaging model creates a new vehicle concept by defining the interior layout and component positions using dimensional chains. The vehicle packaging model is provided by Sethuraman [39] which can create the vehicle package for buses of lengths 5 to 13 m. The model is adapted and parameterized according to the optimization parameters in Table 2.
The model further calculates the mass and dimensions of the components. The battery mass and volume are calculated using the gravimetric and volumetric energy densities [15,22]. The inverter, motor, and transmission mass are calculated using regression functions from [42,43]. The mass for the axle assembly which includes, the axle, suspension, and brakes, is obtained from the technical data sheet of ZF axles [44] and the selection is made using the vehicle’s sprung mass [45]. An empirical function is further used to obtain the cooling power and auxiliary power consumption of the air-conditioning system based on the vehicle’s passenger capacity [45].
In addition to the component sizing and positioning, the packaging model checks for constraint violations of overlapping dimensions if the components’ installation space is insufficient. The output from the packaging calculation consists of the concept’s vehicle specification, which includes the passenger capacity, number of seats, seating-standing ratio, front, and rear overhangs, curb mass, gross vehicle mass, bill of components, and component specifications. Furthermore, the model allows for the visualization of the vehicle concept during postprocessing, as shown in Figure 4a,b of a 6 m AEB and 12 m AEB, respectively.

2.3.3. Vehicle Scheduling

Following the packaging calculation, the timetable of the vehicle concept is evaluated using a two-step method described by Ceder [46], of frequency determination and departure time calculation. The frequency for each hour is calculated using Equation (3). Where F is the frequency, P m j is the maximum passenger load, d o j is the desired occupancy, and F m i n is the minimum frequency at time period j.
F   = max P m j d o j , F m i n
The departure times from the termini are subsequently calculated using the graphical method proposed by [46]. In this method, the cumulative hourly frequency is plotted against time, as shown in Figure 5. The time at which each vehicle departure intersects with the curve is the resulting departure time for the vehicle from the route terminal. The first departure time for each route can be predefined or calculated from the graph. The calculation is repeated for each direction and the remaining routes in the inputs.

2.3.4. Route Simulation

A route simulation is conducted to obtain the passenger occupancy levels in each vehicle trip and calculate the waiting and in-vehicle time of the passengers. The route simulation is conducted in three steps. First, the boarding passengers’ arrival time at each bus stop is calculated by modeling the passenger arrival process as a Poisson process. Next, the destination stop for these passengers is obtained from the origin-destination matrix of the route. The dispatch of the vehicles and boarding and alighting process of the passengers is then simulated.
The vehicles are dispatched from their respective termini according to the departure times obtained from the calculated timetable. The arrival time of the vehicle at the next stop is subsequently calculated using the inter-stop travel times. The vehicle occupancy at the next stop is updated based on the boarding and alighting passenger counts. The alighting passenger counts are known in prior according to the passengers’ destination onboard of the vehicle. The number of boarding passengers is calculated from the waiting passenger count at the bus stop. The vehicle’s dwelling time at the stop is calculated using the boarding and alighting passenger counts using the empirical model in [47]. The calculation is repeated for the following stops and subsequent vehicle departures for all routes. The vehicle occupancy profiles for each trip, waiting, in-vehicle, travel times of the passengers, and the total passenger-km traveled are calculated through the route simulation.

2.3.5. Longitudinal Dynamics Simulation

To evaluate the performance of the powertrain design of the vehicle concept, a longitudinal dynamics simulation (LDS) is conducted using the driving cycle, vehicle specification, passenger occupancy, and auxiliary power consumption of the air-conditioning system. The LDS model developed in [48] is implemented within the framework and simplified to analyze two powertrain architectures shown in Figure 6a, with a single central motor at the rear axle and dual wheel-hub motors at the rear axle (b). Due to the low-floor requirement and insufficient packaging space at the vehicle front axle, powertrain architectures with motors at the front axle are not feasible and are therefore excluded. The LDS model evaluates the energy consumption, acceleration performance, gradeability, and vehicle range for a vehicle concept using the specified driving cycle.

2.3.6. Vehicle Assignment

A vehicle assignment model is developed to evaluate the required fleet size and the total daily distance traveled due to the change in the number of scheduled trips for different vehicle concepts. A mixed integer linear program is formulated to optimally allocate the scheduled trips to each vehicle such that the fleet size and the total distance traveled by the vehicles is minimized.
The model can simulate both depot charging and terminal charging strategies. In the depot charging model, vehicles can only charge between trips by visiting the depot. However, additional energy costs are incurred to travel back and forth from the depot to the termini. In the terminal charging calculation, the vehicles can charge at the route termini before or after a trip or continue to the next trip without charging. The vehicle assignment model finds the cost-optimal allocation of the trips to the vehicles while ensuring the charge levels do not fall below a specified state of charge (SOC).
The mathematical formulation of the model is described by the objective function in Equation (4). Each scheduled trip i to n is represented as a node. An arc x i j connects trips i and j if a vehicle completing trip i can perform trip j. The connection is feasible only if the ending time of trip i and the time taken to travel to the departing terminal of trip j is less than the departure time of trip j. In addition, the depot is represented by node (n+1) which has arcs to and from all scheduled trips, which represent the ‘pull-out’ and ‘pull-in’ operations, respectively.
Each arc x i j between scheduled trips i and j has a cost c i j associated with it equal to the costs arising from the energy consumption during the trip i and from driving to the terminal of the next trip or the depot j. The ‘pull-out’ arcs that originate from the depot have a cost of requiring a new vehicle in addition to the energy cost of driving from the depot to the terminal of trip j.
The constraints in the assignment model are described in Equations (5)–(8). Equations (5) and (6) ensure that a trip cannot be covered more than once. Constraint (7) ensures that the number of vehicles arriving back at the depot should be the same as the number that departed from the depot. Constraint (8) ensures that the vehicle is only assigned trips if it has sufficient charge, q, to cover the trip and drive back to the depot. The variables u and v represent the energy consumption of trip i and the deadheading trip ij respectively, and Q is the battery capacity of the vehicle. The variables are shown in Equation (9) of x i j representing the use of the arc, and q i the charge level of the vehicle at each node, which is calculated during the optimization.
m i n i = 1 n + 1 j = 1 n + 1 c i j x i j
j = 1 n + 1 x i j = 1     i = 1 , 2 , , n
i = 1 n + 1 x i j = 1 j = 1 , 2 , , n
i = 1 n x i , n + 1   j = 1 n x n + 1 , j = 0
q j q i x i j u i   x i j v i j + 1 x i j   Q
x i j 0 , 1 }   ,   q i Q m i n , Q }
Figure 7 shows the output from the vehicle assignment calculation. For each vehicle in the fleet, the schedule, whether it is performing a timetabled trip, an off-service trip, or is waiting/charging along with the SOC over the day, is obtained as shown in Figure 7 (top). Similarly, the trips assigned to the vehicle and terminals visited by the vehicle are obtained, as shown in Figure 7 (bottom). The calculation, therefore, allows for an accurate calculation of the total distances traveled and energy consumed by all the vehicles.

2.3.7. Lifecycle Cost Assessment (LCCA) Model

The LCCA model is used to evaluate the TCO of the vehicles by calculating the net present value (NPV) of the incurred costs during the lifetime of the vehicles. The TCO calculation follows the approach of Ongel [49] and is comprised of the acquisition, energy, battery replacement, cleaning, maintenance, insurance, road tax, and end-of-life costs. The model is adapted to evaluate the TCO of the fleet to allow for a fair cost comparison of vehicles of different sizes since a smaller passenger capacity vehicle would have a lower vehicle acquisition cost. However, a higher number of vehicles would be required to serve the same passenger demand.
The acquisition cost of the vehicle concept is calculated from the component costs, to which the additional expenditures arising from the assembly, labor, and energy costs are added. The component costs are calculated using correlations developed in [19] for the motor, inverter, and gearbox, and battery [50]. The costs of the axle, body, interior, and structure are estimated using the component mass, material mix, and raw material costs according to the method developed by Fuchs [51]. Costs of the sensors, cameras, and processing unit for autonomous driving hardware is taken from [49].
The energy costs are calculated using a fixed electricity price [52] and the total energy demand obtained from the vehicle assignment calculation. Costs due to the battery replacement are estimated by calculating the number of battery packs required during the vehicle’s lifetime. The calculation is based on the cycle life of the battery and the energy throughput calculated in the LDS. The costs from cleaning, maintenance, insurance, road tax, and end-of-life are calculated according to the described methods in [49].
Using the NPV approach, the annual costs over the assumed vehicle lifetime of 17 years is calculated and discounted to present value to obtain the TCO. The cost is further normalized by the total passenger-km traveled to calculate the total costs in SGD/passenger-km.

2.3.8. Lifecycle Assessment Model (LCA)

A scalable LCA model provided by [53] is used to analyze the GHG emissions of the vehicle concepts during the phases of production, distribution, use phase, and end-of-life. The model is developed from the Umberto-LCA [54] software, which uses the lifecycle inventory databases from Ecoinvent—version 3.5 [55]. The model calculates the production phase emissions of obtaining and converting raw materials into finished components based on the component’s mass and material mix. The component mass and material composition for the body, structure, chassis, powertrain, and cooling are estimated from the packaging model. The emissions during the distribution of the vehicles to Singapore is further calculated from the Ecoinvent database.
To calculate the emissions in the use phase, a Well-to-Wheel assessment is done, which consists of the Well-to-Tank (WTT) and Tank-to-Wheel (TTW) stages. Since the vehicle concepts analyzed are electric, the TTW emissions are assumed to be zero. The WTT emissions are calculated based on the emissions in the electricity production, using the energy mix of Singapore [56,57] and the vehicle fleet’s total energy consumption determined in the vehicle assignment calculation. The use-phase emissions are further calculated over the assumed vehicle lifetime of 17 years.
Lastly, the vehicles’ end-of-life emissions are estimated due to energy use in material recycling and scraping processes. Based on the component mass, material composition, and material recycling rates [58,59,60,61], the processes’ energy demand and emissions are calculated. The total emissions over the vehicles’ lifetime are then calculated and normalized by the total passenger-km to calculate the emissions in g-CO2/passenger-km.

2.3.9. Property Evaluation and Parameter Variation

In the last step of the calculation, the objective function is evaluated using each attribute’s value functions and the technical specifications obtained from the preceding calculations. A parameter variation is conducted at the end of each generation by the NSGA-II algorithm through a selection, cross-over and mutation operation on the current generation’s population to calculate the vehicle parameters for the next generation. Furthermore, solutions that violate the constraints are removed during the selection operation. The optimization constraints are geometric inequalities that ensure that the component dimensions do not exceed the installation space and prevent any geometric overlap between components.

3. Case Study

Using the developed model, a case study is conducted on a single bi-directional bus route in Singapore to find the Pareto optimal concepts and analyze the vehicle’s impacts on costs, property fulfillment, emissions, and powertrain design.
The bus route analyzed in the case study is 16.2 km in length and is shown in Figure 8. The Bus rapid transit (BRT) driving cycle [62] is used as the speed profile to calculate the vehicle’s energy consumption in the LDS simulation, and a depot charging operation is analyzed with 150 kW chargers available only at the depot.

4. Results

The results of the design optimization are presented in this section. Using the genetic algorithm, the optimal solutions of vehicle concepts are calculated for the analyzed route. Figure 9a depicts the Pareto front showing the optimal trade-off between the property fulfillment and the TCO. The property fulfillment represents the value to the stakeholders on a scale of 0 to 10.
Figure 9b shows the influence of the vehicle size on the TCO and property fulfillment. Smaller vehicles have a higher property fulfillment value primarily due to improvements in the service performance attributes. Therefore, the property fulfillment increases to 9.35 for a vehicle size of 20 passengers compared to 8.81 for a 94-passenger vehicle. However, the total costs for the 20-passenger vehicle increase to 0.201 SGD/passenger-km from 0.091 SGD/passenger-km.
The TCO increases for the smaller vehicle sizes due to the larger fleet size and the increase in distance traveled by the fleet per day as shown in Figure 10a,b respectively. The fleet size increases from 16 to 69 vehicles while the distance traveled per day increases from 1280 to 5988 km for vehicle sizes of 94 and 20 passengers, respectively.
The waiting time for the passengers however reduces from 18 min to around 6 min for the smaller vehicle size of 20 passengers. The overall service performance can therefore be significantly improved with the use of small capacity vehicles for the analyzed route. Figure 11b shows how the number of timetabled trips changes with the vehicle size. The scheduled trips increase from 75 trips for 94-passenger vehicle to 340 trips for a 20-passenger vehicle. The scheduling algorithm calculates the bus frequencies according to the passenger demand at each hour and the vehicle’s desired occupancy/seating capacity. Therefore, the number of scheduled trips significantly increases for smaller vehicle capacities, as seen in Figure 11b.
Figure 12a shows the influence of the vehicle size on energy consumption. For the analyzed driving cycle, the vehicle’s energy consumption increases linearly from 0.45 kWh/km for a 20-passenger vehicle to 1.35 kWh/km for a 94-passenger vehicle. However, considering the overall fleet, the 20-passenger vehicle has a higher energy consumption of 0.12 kWh/passenger-km, due to the longer distances traveled, compared to 0.08 kWh/passenger-km for a 94-passenger vehicle.
Similarly, due to the increase in energy consumption, the GHG emissions of smaller vehicles also increase from 41.5 to 65.6 g-CO2/passenger-km for vehicle sizes of 94 and 20 passengers, respectively, as shown in Figure 12b.
Figure 13 shows the required motor power and battery capacity for different vehicle sizes. In Figure 13a, all feasible combinations of installed motor power simulated for different vehicle sizes are shown. The minimum motor power required to drive according to the analyzed driving cycle increases from 115 kW to 310 kW for a 20 and 94 passenger vehicle, respectively. Concepts with installed power below the curve did not meet the torque and speed requirements.
Figure 13b shows the minimum battery capacity required for different vehicle sizes. The minimum required battery size increases from 105 kWh for a 20-passenger vehicle to around 250 kWh for a 94-passenger vehicle for the depot charging strategy. The plot further shows the maximum battery size that can be installed and packaged in the vehicle due to the limited packaging space in the underfloor.

5. Conclusions

This paper presents a holistic framework to identify the optimal vehicle specifications of AEBs based on the routes in which the buses will operate. To calculate the optimal specifications, a multi-objective, multi-criteria objective function is formulated by analyzing the requirements from the perspective of the stakeholders. The requirements are categorized into nine properties of service performance, accessibility, comfort, functionality, information, safety, longitudinal dynamics, environmental performance, and costs.
The optimization is formulated with two objectives to find the optimal trade-off between the overall benefit to the stakeholders and the total costs. The first objective maximizes the weighted sum of the properties, while the second objective minimizes the TCO.
To evaluate the objective functions, a simulation framework is developed. The framework derives AEB concepts using a vehicle packaging model. The vehicle’s impacts on the properties are subsequently analyzed in a vehicle scheduling, route simulation, LDS, vehicle assignment, lifecycle cost, and lifecycle emissions calculations. The NSGA-II genetic algorithm is used to solve the objective function to find the Pareto optimal solutions.
A case study is conducted using the developed model to find the optimal vehicle specifications of AEBs for a bus route in Singapore. The results showed that the passengers’ waiting time could be reduced to around 6 min using a vehicle size of 20 passengers compared to 18 min with a 94-passenger vehicle for the analyzed bus route. However, the costs and GHG emissions increase due to the larger fleet required and the longer distances traveled with the 20-passenger vehicle.
Moreover, the parameters for the powertrain design and the battery capacity can be identified through the optimization. For the analyzed case study, the minimum motor size required was found to be 115 kW for a 20-passenger vehicle and 310 kW for a 94-passenger vehicle. Similarly, the minimum battery size needed was calculated to be 105 kWh and 250 kWh for the 20 and 94 passenger vehicles, respectively.
Using the proposed model, vehicle manufacturers and bus operators can simulate different scenarios to find the optimal vehicle specifications for their bus routes and analyze the impacts on the benefit to the users, costs, and emissions. Future work will extend the analysis to consider multiple routes and investigate the influence of different charging methods on the vehicle specifications, costs, and emissions.

Author Contributions

A.P. worked on the conceptualization, implementation, and analysis of the results. S.S. was involved in the formulation of the objective function and revising the manuscript. A.O. is the principal investigator of this project and was involved in the supervision of the project. M.L. made an essential contribution to the conception of the research project and revised the paper critically for important intellectual content. M.L. gave the final approval to the version to be published and agrees to all aspects of the work. As guarantor, M.L. accepts responsibility for the overall integrity of the paper. All authors have read and agreed to the published version of the manuscript.

Funding

The research was conducted under the Campus for Research Excellence and Technological Enterprise (CREATE) with the financial support of the Singapore National Research Foundation (NRF).

Conflicts of Interest

The authors declare no conflict of interest. The funders had no role in the design of the study; in the collection, analyses, or interpretation of data; in the writing of the manuscript, or in the decision to publish the results.

References

  1. Wadud, Z. Fully automated vehicles: A cost of ownership analysis to inform early adoption. Transp. Res. Part A Policy Pract. 2017, 101, 163–176. [Google Scholar] [CrossRef]
  2. Greenblatt, J.B.; Saxena, S. Autonomous taxis could greatly reduce greenhouse-gas emissions of US light-duty vehicles. Nat. Clim. Chang. 2015, 5, 860–863. [Google Scholar] [CrossRef]
  3. Azad, M.; Hoseinzadeh, N.; Brakewood, C.; Cherry, C.R.; Han, L.D. Fully Autonomous Buses: A Literature Review and Future Research Directions. J. Adv. Transp. 2019, 2019, 1–16. [Google Scholar] [CrossRef] [Green Version]
  4. Rau, A.; Tian, L.; Jain, M.; Xie, M.; Zhou, Y. Dynamic autonomous road transit (DART) for use-case capacity more than bus. Transp. Res. Procedia 2018, 41, 812–823. [Google Scholar] [CrossRef]
  5. Project HEAT—Hamburger Hochbahn AG. Available online: https://www.hochbahn.de/hochbahn/hamburg/en/home/projects/expansion_and_projects/project_heat (accessed on 1 December 2020).
  6. Navya. AUTONOM® SHUTTLE: For more fluid mobility. Available online: https://navya.tech/wp-content/uploads/documents/Brochure_Shuttle_EN.pdf (accessed on 1 December 2020).
  7. Easy Mile. An Introduction to the EZ10. Available online: https://coloradotransit.com/wp-content/uploads/2018/10/EasyMile-CASTA-Oct-2018.pdf (accessed on 1 December 2020).
  8. 2getthere. GRT Vehicle: Automated Minibus—2getthere. Available online: https://www.2getthere.eu/technology/vehicle-types/grt-vehicle-automated-minibus/ (accessed on 1 December 2020).
  9. Kane, M. Electric, Autonomous and Modular Scania NXT Unveiled. Available online: https://insideevs.com/news/354248/electric-autonomous-modular-scania-nxt/ (accessed on 1 December 2020).
  10. Nicoletti, L.; Romano, A.; König, A.; Schockenhoff, F.; Lienkamp, M. Parametric Modeling of Mass and Volume Effects for Battery Electric Vehicles, with Focus on the Wheel Components. WEVJ 2020, 11, 63. [Google Scholar] [CrossRef]
  11. Fuchs, S.; Lienkamp, M. Parametric Modelling of Mass and Efficiency of New Vehicle Concepts. Atz Worldw 2013, 115, 60–67. [Google Scholar] [CrossRef]
  12. Felgenhauer, M.; Nicoletti, L.; Schockenhoff, F.; Angerer, C.; Lienkamp, M. Empiric Weight Model for the Early Phase of Vehicle Architecture Design. In Proceedings of the 2019 Fourteenth International Conference on Ecological Vehicles and Renewable Energies (EVER), Monte-Carlo, Monaco, 8–10 May 2019; pp. 1–8. [Google Scholar] [CrossRef]
  13. Koenig, A.; Schockenhoff, F.; Koch, A.; Lienkamp, M. Concept Design Optimization of Autonomous and Electric Vehicles. In Proceedings of the 8th International Conference on Power Science and Engineering, (ICPSE 2019), Dublin, Ireland, 2–4 December 2019. [Google Scholar]
  14. Wiedemann, E.; Meurle, J.; Lienkamp, M. Optimization of Electric Vehicle Concepts Based on Customer-Relevant Characteristics; SAE Technical Paper 2012-01-0815; SAE: Warrendale, PA, USA, 2012. [Google Scholar] [CrossRef]
  15. Matz, S. Nutzerorientierte Fahrzeugkonzeptoptimierung in Einer multimodalen Verkehrsumgebung. Ph.D. Thesis, Technische Universität München, München, Germany, 2015. [Google Scholar]
  16. Kuchenbuch, K. Methodik zur Identifikation und zum Entwurf Packageoptimierter Elektrofahrzeuge. Ph.D. Thesis, Technische Universität Braunschweig, Braunschweig, Germany, 2012. [Google Scholar]
  17. Holjevac, N.; Cheli, F.; Gobbi, M. Multi-objective vehicle optimization: Comparison of combustion engine, hybrid and electric powertrains. Proc. Inst. Mech. Eng. Part D J. Automob. Eng. 2020, 234, 469–487. [Google Scholar] [CrossRef]
  18. Lin, X.; Kerler, M.; Birke, K.P.; Lienkamp, M. Optimal Battery Cell Design for Electric Vehicles—A Holistic Method with Consideration of Ageing due to Electrothermal Gradients. In Proceedings of the 8th International Conference on Power Science and Engineering, (ICPSE 2019), Dublin, Ireland, 2–4 December 2019; ISBN 9781728160818. [Google Scholar]
  19. Angerer, C.; Krapf, S.; Buß, A.; Lienkamp, M. Holistic modeling and optimization of electric vehicle Powertrains considering longitudinal performance, vehicle Dynamics, costs and energy consumption. In Proceedings of the ASME 2018 International Design Engineering Technical Conferences and Computers and Information in Engineering Conference, Quebec City, QC, Canada, 26–29 August 2018. [Google Scholar]
  20. Schönknecht, A.; Babik, A.; Rill, V. Electric Powertrain System Design of BEV and HEV Applying a Multi Objective Optimization Methodology. Transp. Res. Procedia 2016, 14, 3611–3620. [Google Scholar] [CrossRef] [Green Version]
  21. Scholl, M.; Minnerup, K.; Reiter, C.; Bernhardt, B.; Weisbrodt, E.; Newiger, S. Optimization of a Thermal Management System for Battery Electric Vehicles. In Proceedings of the 2019 Fourteenth International Conference on Ecological Vehicles and Renewable Energies (EVER), Monte-Carlo, Monaco, 8–10 May 2019; pp. 1–10. [Google Scholar] [CrossRef]
  22. Fries, M.; Lehmeyer, M.; Lienkamp, M. Multi-criterion optimization of heavy-duty powertrain design for the evaluation of transport efficiency and costs. In Proceedings of the IEEE 20th International Conference on Intelligent Transportation Systems, Yokohama, Japan, 16–19 October 2017. [Google Scholar]
  23. Ziemann. Zielsystemmanagement für die Produktentstehung von PKW; Books on Demand: Norderstedt, Germany, 2007. [Google Scholar]
  24. Meurle, J.; Rigel, S.; Muigg, A. Fahrzeugeigenschaften—Erwartungshaltung des Kunden und Technische Umsetzbarkeit; Zenloop: Graz, Austria, 2009. [Google Scholar]
  25. Weber, J. Automotive Development Processes; Springer: Berlin/Heidelberg, Germany, 2009; ISBN 978-3-642-01252-5. [Google Scholar]
  26. Schockenhoff, F.; König, A.; Koch, A.; Lienkamp, M. Customer-Relevant Properties of Autonomous Vehicle Concepts. Procedia CIRP 2020, 91, 55–60. [Google Scholar] [CrossRef]
  27. Wiedemann, E. Ableitung von Elektrofahrzeugkonzepten aus Eigenschaftszielen. Ph.D. Thesis, Technische Universität München, München, Germany, 2013. [Google Scholar]
  28. Moataz, M.; Ryan, G.; Mark, F.; Pavlos, K. Electric buses: A review of alternative powertrains. Renew. Sustain. Energy Rev. 2016, 62, 673–684. [Google Scholar] [CrossRef]
  29. Lajunen, A. Energy consumption and cost-benefit analysis of hybrid and electric city buses. Transp. Res. Part C Emerg. Technol. 2014, 38, 1–15. [Google Scholar] [CrossRef]
  30. Harris, A.; Soban, D.; Smyth, B.M.; Best, R. A probabilistic fleet analysis for energy consumption, life cycle cost and greenhouse gas emissions modelling of bus technologies. Appl. Energy 2020, 261, 114422. [Google Scholar] [CrossRef]
  31. Lajunen, A. Lifecycle costs and charging requirements of electric buses with different charging methods. J. Clean. Prod. 2018, 172, 56–67. [Google Scholar] [CrossRef]
  32. Kunith, A.; Mendelevitch, R.; Goehlich, D. Electrification of a city bus network—An optimization model for cost-effective placing of charging infrastructure and battery sizing of fast-charging electric bus systems. Int. J. Sustain. Transp. 2017, 11, 707–720. [Google Scholar] [CrossRef] [Green Version]
  33. Teichert, O.; Chang, F.; Ongel, A.; Lienkamp, M. Joint Optimization of Vehicle Battery Pack Capacity and Charging Infrastructure for Electrified Public Bus Systems. IEEE Trans. Transp. Electrif. 2019, 5, 672–682. [Google Scholar] [CrossRef]
  34. van Kooten Niekerk, M.E.; van den Akker, J.M.; Hoogeveen, J.A. Scheduling electric vehicles. Public Transp. 2017, 9, 155–176. [Google Scholar] [CrossRef]
  35. Wang, Y.; Huang, Y.; Xu, J.; Barclay, N. Optimal recharging scheduling for urban electric buses: A case study in Davis. Transp. Res. Part E Logist. Transp. Rev. 2017, 100, 115–132. [Google Scholar] [CrossRef]
  36. Nicoletti, L.; Bronner, M.; Danquah, B.; Koch, A.; Konig, A.; Krapf, S.; Pathak, A.; Schockenhoff, F.; Sethuraman, G.; Wolff, S.; et al. Review of Trends and Potentials in the Vehicle Concept Development Process. In Proceedings of the 2020 Fifteenth International Conference on Ecological Vehicles and Renewable Energies (EVER), Monte-Carlo, Monaco, 10–12 September 2020; pp. 1–15. [Google Scholar] [CrossRef]
  37. Scheuermann, S. Development of a Customer-Centric Approach to Derive Autonomous Electric Vehicle Concepts for Public Transportation in Singapore. Master’s Thesis, Technical University of Munich, Munich, Germany, 2020. [Google Scholar]
  38. Aigner, J. Zur zuverlässigen Beurteilung von Fahrzeugen. ATZ Automobiltechnische Zeitschrift 1982, 84, 447–450. [Google Scholar]
  39. Sethuraman, G.; Schwarz, M.; Maxl, S.; Ongel, A.; Lienkamp, M.; Ng, H.W.; Raksincharoensak, P. Development of an Overall Vehicle Sizing and Packaging Tool for Autonomous Electric Buses in the Early Concept Phase. SAE Int. J. Commer. Veh. 2020, 13, 23–42. [Google Scholar] [CrossRef]
  40. Nicoletti, L.; Mayer, S.; Brönner, M.; Schockenhoff, F.; Lienkamp, M. Design Parameters for the Early Development Phase of Battery Electric Vehicles. WEVJ 2020, 11, 47. [Google Scholar] [CrossRef]
  41. Deb, K.; Pratap, A.; Agarwal, S.; Meyarivan, T. A fast and elitist multiobjective genetic algorithm: NSGA-II. IEEE Trans. Evol. Comput. 2002, 6, 182–197. [Google Scholar] [CrossRef] [Green Version]
  42. Pesce, T. Ein Werkzeug zur Spezifikation von Effizienten Antriebstopologien für Elektrofahrzeuge. Ph.D. Thesis, Technische Universität München, München, Germany, 2014. [Google Scholar]
  43. Seeger, F. Energetische Modellierung Verschiedener Systeme zur Momentenverteilung für ein Adaptives Antriebsstrangmodell. Semester Thesis, Technische Universität München, München, Germany, 2017. [Google Scholar]
  44. Friedrichshafen, Z.F. Axle & Transmission Systems for Buses. Available online: https://www.zf.com/master/media/corporate/m_zf_com/company/download_center/products/trucks/2020_3/TU_Product_Overview_202012_DE_EN_LowRes.pdf (accessed on 15 December 2020).
  45. Sethuraman, G.; Tran, P.R.; Ongel, A.; Lienkamp, M.; Raksincharoensak, P. Development of a parametric packaging and sizing tool for autonomous electric bus system. Proc. Inst. Mech. Eng. Part D J. Automob. Eng. 2020. [Google Scholar] [CrossRef]
  46. Ceder, A.; Hassold, S.; Dano, B. Approaching even-load and even-headway transit timetables using different bus sizes. Public Transp. 2013, 5, 193–217. [Google Scholar] [CrossRef]
  47. Sun, L.; Tirachini, A.; Axhausen, K.W.; Erath, A.; Lee, D.-H. Models of bus boarding and alighting dynamics. Transp. Res. Part A Policy Pract. 2014, 69, 447–460. [Google Scholar] [CrossRef] [Green Version]
  48. Pathak, A.; Sethuraman, G.; Krapf, S.; Ongel, A.; Lienkamp, M. Exploration of Optimal Powertrain Design Using Realistic Load Profiles. World Electr. Veh. J. 2019, 10, 56. [Google Scholar] [CrossRef] [Green Version]
  49. Ongel, A.; Loewer, E.; Roemer, F.; Sethuraman, G.; Chang, F.; Lienkamp, M. Economic Assessment of Autonomous Electric Microtransit Vehicles. Sustainability 2019, 11, 648. [Google Scholar] [CrossRef] [Green Version]
  50. Fries, M.; Kerler, M.; Rohr, S.; Sinning, M.; Schickram, S.; Lienkamp, M.; Kochhan, R.; Fuchs, S.; Reuter, B.; Burda, P.; et al. An Overview of Costs for Vehicle Components, Fuels, Greenhouse Gas Emissions and Total Cost of Ownership—Update 2017. Res. Gate 2017. [Google Scholar] [CrossRef]
  51. Fuchs, S. Verfahren zur Parameterbasierten Gewichtsabschätzung neuer Fahrzeugkonzepte. Ph.D. Thesis, Technische Universität München, München, Germany, 2014. [Google Scholar]
  52. Energy Market Authority. Singapore Energy Statistics—Energy Prices. Available online: https://www.ema.gov.sg/singapore-energy-statistics/Ch05/index5 (accessed on 16 December 2020).
  53. Sethuraman, G. Vehicle Component Configuration Design and Packaging in Virtual Environment for Autonomous Electric Buses. Ph.D. Thesis, Tokyo University of Agriculture and Technology, Tokyo, Japan, 2020. [Google Scholar]
  54. Umberto LCA+. Umberto LCA+. Available online: https://www.ifu.com/en/umberto/lca-software/ (accessed on 8 May 2020).
  55. Ecoinvent. Ecoinvent 3.5. Available online: https://www.ecoinvent.org/database/olderversions/ecoinvent-35/ecoinvent-35.html (accessed on 3 February 2019).
  56. Pathak, A.; Sethuraman, G.; Ongel, A.; Lienkamp, M. Impacts of electrification & automation of public bus transportation on sustainability—A case study in Singapore. Forsch. Ing. 2020. [Google Scholar] [CrossRef]
  57. EMA Supply. Energy Market Authority|Energy Supply. Available online: https://www.ema.gov.sg/cmsmedia/Publications_and_Statistics/Publications/ses/2018/energy-supply/index.html (accessed on 7 May 2020).
  58. Kelly, S.; Apelian, D. Automotive Aluminum Recycling at End of Life: A Grave-to-Gate Analysis. Available online: http://www.drivealuminum.org/wp-content/uploads/2016/06/Final-Report-Automotive-Aluminum-Recycling-at-End-of-Life-A-Grave-to-Gate-Analysis.pdf (accessed on 16 December 2020).
  59. LithoRec II. Recycling of EV-Lithium-Ion-Batteries. Available online: http://www.lithorec2.de/index.php/en/ (accessed on 1 October 2019).
  60. McGlothlin, S. Copper Recycling Process Technology in End of Life Vehicle (ELV) Shredder Plants. Available online: https://www.metalbulletin.com/events/download.ashx/document/speaker/6539/a0ID000000X0jUWMAZ/Presentation (accessed on 1 October 2019).
  61. WorldAutoSteel. Recycling. Available online: https://www.worldautosteel.org/life-cyclethinking/recycling/ (accessed on 2 July 2019).
  62. Lai, J.; Yu, L.; Song, G.; Guo, P.; Chen, X. Development of City-Specific Driving Cycles for Transit Buses Based on VSP Distributions: Case of Beijing. J. Transp. Eng. 2013, 139, 749–757. [Google Scholar] [CrossRef]
Figure 1. Overview of the overall methodology.
Figure 1. Overview of the overall methodology.
Wevj 12 00030 g001
Figure 2. Value Functions showing the correlation between the objective value and technical specifications. Value function of (a) waiting time, (b) seating ratio, (c) seat pitch, (d) standing space, (e) vehicle top speed, (f) wheelchair zones.
Figure 2. Value Functions showing the correlation between the objective value and technical specifications. Value function of (a) waiting time, (b) seating ratio, (c) seat pitch, (d) standing space, (e) vehicle top speed, (f) wheelchair zones.
Wevj 12 00030 g002
Figure 3. Overall simulation framework to evaluate the objective function.
Figure 3. Overall simulation framework to evaluate the objective function.
Wevj 12 00030 g003
Figure 4. Vehicle package visualization of a 6 m AEB (a) and 12 m AEB (b).
Figure 4. Vehicle package visualization of a 6 m AEB (a) and 12 m AEB (b).
Wevj 12 00030 g004
Figure 5. Determination of departure times using the graphical method in [46].
Figure 5. Determination of departure times using the graphical method in [46].
Wevj 12 00030 g005
Figure 6. Powertrain Architectures of single motor rear wheel drive (a) and (b) dual wheel-hub motors.
Figure 6. Powertrain Architectures of single motor rear wheel drive (a) and (b) dual wheel-hub motors.
Wevj 12 00030 g006
Figure 7. Showing the vehicle schedule and the state of charge (top), and the location and trips assigned to the vehicle during the day (bottom).
Figure 7. Showing the vehicle schedule and the state of charge (top), and the location and trips assigned to the vehicle during the day (bottom).
Wevj 12 00030 g007
Figure 8. Route analyzed in this case study and the location of the depot.
Figure 8. Route analyzed in this case study and the location of the depot.
Wevj 12 00030 g008
Figure 9. (a) Pareto optimal solutions of the vehicle concepts for the analyzed route. (b) The effect of vehicle size on the costs and value to the users.
Figure 9. (a) Pareto optimal solutions of the vehicle concepts for the analyzed route. (b) The effect of vehicle size on the costs and value to the users.
Wevj 12 00030 g009
Figure 10. Influence of vehicle size on (a) fleet size and (b) on distance traveled per day.
Figure 10. Influence of vehicle size on (a) fleet size and (b) on distance traveled per day.
Wevj 12 00030 g010
Figure 11. Influence of vehicle size on (a) passenger waiting time, and (b) number of scheduled trips.
Figure 11. Influence of vehicle size on (a) passenger waiting time, and (b) number of scheduled trips.
Wevj 12 00030 g011
Figure 12. Influence of vehicle size on (a) energy consumption (b) GHG emissions.
Figure 12. Influence of vehicle size on (a) energy consumption (b) GHG emissions.
Wevj 12 00030 g012
Figure 13. Shows the solution space and minimum required (a) motor power and (b) battery capacity.
Figure 13. Shows the solution space and minimum required (a) motor power and (b) battery capacity.
Wevj 12 00030 g013
Table 1. Identified properties and attributes of AEBs.
Table 1. Identified properties and attributes of AEBs.
PropertyAttributes
Service PerformanceWaiting time
Travel time
Seat availability
AccessibilityEntry height
Wheelchair zones
Number of doors
ComfortSeat width
Legroom
Standing space
Headroom
Thermal comfort
Ride comfort
FunctionalityLuggage storage
Power outlets
Bicycle storage
InformationHuman-machine interfaces
SafetyHandrails and handles
Seatbelts
Security/surveillance cameras
Longitudinal DynamicsTop speed
Acceleration
Gradeability
Environmental PerformanceLifecycle greenhouse gas emissions
CostsTotal Cost of Ownership
Table 2. Optimization parameters of the vehicle concept.
Table 2. Optimization parameters of the vehicle concept.
Vehicle ParametersLower BoundUpper BoundType
Vehicle Height2100 mm3000 mmContinuous
Vehicle Length5000 mm13000 mmContinuous
Vehicle Width2500 mm2600 mmContinuous
Interior LayoutLayout 1Layout 2Categorical
Wheelbase2500 mm9000 mmContinuous
Seat Pitch650 mm850 mmContinuous
Seat Width400 mm550 mmContinuous
Standing Space2 Passengers/m28 Passengers/m2Continuous
Powertrain TopologyTopology 1Topology 2Categorical
Total Power40 kW400 kWContinuous
Gear Ratio130Continuous
Battery Capacity30 kWh350 kWhContinuous
Wheelchair Zones02Discrete
Number of Doors12Discrete
Publisher’s Note: MDPI stays neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Share and Cite

MDPI and ACS Style

Pathak, A.; Scheuermann, S.; Ongel, A.; Lienkamp, M. Conceptual Design Optimization of Autonomous Electric Buses in Public Transportation. World Electr. Veh. J. 2021, 12, 30. https://0-doi-org.brum.beds.ac.uk/10.3390/wevj12010030

AMA Style

Pathak A, Scheuermann S, Ongel A, Lienkamp M. Conceptual Design Optimization of Autonomous Electric Buses in Public Transportation. World Electric Vehicle Journal. 2021; 12(1):30. https://0-doi-org.brum.beds.ac.uk/10.3390/wevj12010030

Chicago/Turabian Style

Pathak, Aditya, Silvan Scheuermann, Aybike Ongel, and Markus Lienkamp. 2021. "Conceptual Design Optimization of Autonomous Electric Buses in Public Transportation" World Electric Vehicle Journal 12, no. 1: 30. https://0-doi-org.brum.beds.ac.uk/10.3390/wevj12010030

Article Metrics

Back to TopTop