This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Experimental Investigation and Mathematical Presentation of Rate of Heat Release in Diesel Engines Dependent upon Engine Operating Conditions
Annotation ability available
Sector:
Language:
English
Abstract
To predict the behavior of diesel engines with altered operating conditions by means of cycle simulation, a knowledge of the rate of heat release is necessary. On a medium-speed diesel engine, experimental investigations were carried out to determine the relationship between the heat release diagram and parameters such as equivalence ratio, charge air pressure, charge air temperature, engine speed, and injection timing. For a mathematical representation of the results, the actual heat release diagrams are replaced by simplified “Wiebe” heat release diagrams, which have the same beginning and duration of combustion; the shape, however, is simplified and chosen so that if they are used for cycle simulations, the calculated values of peak pressure, power output, and fuel consumption are in agreement with the measured data. Such a simplified Wiebe heat release diagram is characterized by four parameters: the beginning and duration of combustion, the Wiebe parameter m, and the equivalence ratio. Empirical correlations are established whereby it is possible to predict variations of these parameters with altered operating conditions. If, for an engine under consideration, the heat release diagram and the rate of injection are known from a measurement for one particular operating point, by means of these correlations it is possible to predict the heat release diagram for any altered operating conditions.
Recommended Content
Authors
Topic
Citation
Woschni, G. and Anisits, F., "Experimental Investigation and Mathematical Presentation of Rate of Heat Release in Diesel Engines Dependent upon Engine Operating Conditions," SAE Technical Paper 740086, 1974, https://doi.org/10.4271/740086.Also In
References
- Wacker E. Strecker E. Sarsten A. Haaland E. “Finite Element-Programme zur Berechnung von Brennraum-Bauteilen.” (Analysis of Components of Combustion Chambers by Means of Finite-Element Programming.) MTZ 32 8 1971 267
- Woschni G. “Elektronische Berechnung von Verbrennungsmotorkreisprozessen.” (Electronic Simulation of Internal Combustion Engine Cycles.) MTZ 26 11 1965 439
- Woschni G. “Die Berechnung der Wandverluste und der thermischen Belastung der Bauteile von Dieselmotoren.” (Computing the Heat Transfer and the Thermal Load of Diesel Engine Components.) MTZ 31 12 1970 491
- Woschni G. “Universally Applicable Equation for Instantaneous Heat Transfer Coefficient in the Internal Combustion Engine.” SAE Transactions 76 1968 paper 670931
- Melcher K. “Elektronische Berechnung der Vorgange in Einspritzsystemen.” (Electronic Simulation of the Injection System.) MTZ 24 8 1963 277
- Sitkei G. “Kraftstoffaufbereitung und Verbrennung bei Dieselmotoren.” (Fuel Preparation and Combustion in Diesel Engines.) Berlin, Gottingen, Heidelberg Springer 1964
- Wanscheidt W. A. “Theorie der Dieselmotoren.” (Theory of Diesel Engines.) Berlin Verlag Technik 1955
- Neumann K. “Kinetische Analyse des Verbrennungsvorganges in der Dieselmaschine.” (Kinetic Analysis of the Combustion Process in the Diesel Engine.) 1936
- Inosemzew N. “Thermodynamik und Kinetik der chemischen Reaktionen.” (Thermodynamics and Kinetics of Chemical Reactions.) Moscow 1950
- Lange W. Woschni G. “Thermodynamische Auswertung von Indikatordiagrammen, elektronisch gerechnet.” (Thermodynamic Analysis of Indicator Diagrams by Electronic Means.) MTZ 25 7 1964 284
- Woschni G. Anisits F. “Elektronische Berechnung des Einspritzverlaufes im Dieselmotor aus dem gemessenen Druckverlauf in der Einspritzleitung.” (Computing the Rate of Injection from the Pressure Measured in the Injection Line.) MTZ 30 7 1969 238
- Austen A. E. W. Lyn W. T. “Relation between Fuel Injection and Heat Release in a Direct-Injection Engine and the Nature of the Combustion Process.” Proc. IME (A. D.) 1 1960-1961 47 Lyn W. T. “Einige Probleme der Verbrennung in Dieselmotoren.” (Some Problems of Combustion in Diesel Engines.) MTZ 27 4 1966
- Shipinski J. Uyehara O. A. Myers P. S. “Experimental Correlation between Rate-of-Injection and Rate-of-Heat-Release in a Diesel Engine.” ASME Paper 68
- Wiebe I. I. “Brennverlauf und Kreisprozeβ von Verbrennungsmotoren.” (Heat Release and Working Cycle of Internal Combustion Engines.) Berlin Verlag Technik
- Schmidt F. A. F. “Verbrennungskraftmaschine.” (Internal Combustion Engines.) Berlin, Heidelberg, New York Springer 530
- Wolfer H. “Der Zünderzug im Dieselmotor.” (The Ignition Delay in Diesel Engines.) 1938
- Sitkei G. “Über den dieselmotorischen Zündverzug.” (On the Ignition Delay in Diesel Engines.) MTZ 24 6 1963 190
- Anisits F. “Experimentelle Bestimmung und analytische Fassung der Brennverläufe für Vorkammer-Dieselmotoren als Randbedingung für die Prozeβberechnung.” (Experimental Determination and Analytic Form of the Heat Release Diagram of Divided-chamber Diesel Engines as a Boundary Condition for Cycle Simulation.) 1973