Design and Analysis of a Photonic Crystal Based Planar Antenna for THz Applications

Abstract

Modern advancements in wearable smart devices and ultra-high-speed terahertz (THz) communication systems require low cost, low profile, and highly efficient antenna design with high directionality to address the propagation loss at the THz range. For this purpose, a novel shape, high gain antenna for THz frequency range applications is presented in this work. The proposed antenna is based on a photonic bandgap (PBG)-based crystal polyimide substrate which gives optimum performance in terms of gain (9.45 dB), directivity (9.99 dBi), and highly satisfactory VSWR (<1) at 0.63 THz. The performance of the antenna is studied on PBGs of different geometrical configurations and the results are compared with the antenna based on the homogeneous polyimide-based substrate. The effects of variations in the dimensions of the PBG unit cells are also studied to achieve a −10 dB bandwidth of 28.97 GHz (0.616 to 0.64 THz).

1. Introduction

The Terahertz (THz) frequency band (0.1 to 10 THz) has attained a lot of interest in the last decade due to the development of a cost-effective generation of THz signals [1] and its applications to fulfill the requirements of wideband and high data rate. Electromagnetic waves at THz have numerous applications for wireless communication [2], spectroscopy [3], remote sensing [4], medical diagnosis [5,6], high-speed communication [7], and radio astronomy [8]. Transmission in the THz frequency band can provide data rates of up to 100 Gb/s per stream for future communication systems [9]. Especially for short-distance indoor or outdoor hotspots, wireless local area networks at terabits data rates (T-WLAN) [10] are potential candidates to provide wireless access, which can also be integrated with ultra-high-capacity optical fiber links [11] for Fixed Wireless Access (FWA). To support low cost and reliable transmission of THz signals, several design considerations are required for the transmission antenna such as low cost, compact size, large bandwidth, and high gain. Photoconductive materials making use of photo mixing radiators is considered the most general technique for THz transmission, but the low gain and phase noise (induced due to the line width of the remote laser source) is a major bottleneck. Directivity is an essential requirement to compensate for high free-space path loss at the THz range. As an alternative, microstrip patch antennas can make use of the high frequency of THz operation to provide a low-profile design, but their performance suffers due to the surface waves, resulting in low gain and low bandwidth [12]. Although the low bandwidth is an inherent feature of the microstrip antennas due to its resonant nature, high directivity with large bandwidth can be achieved using the photonic crystal (PC) technique for a robust and effective transmission design [13]. In PC-based design, photonic bandgap (PBG) structures are integrated into microstrip patch antennas to achieve better radiation properties. The PBG-based substrates can be used to overcome the limitation of surface waves [13] in planar microstrip antennas. This is achieved by embedding photonic crystals in the dielectric substrate. In this way, the PBG structure results in an improvement in gain, directivity, bandwidth, and radiation pattern by providing high attenuation for an undesired band of frequencies and resistance against the surface waves travelling within the substrate. Several variants of PBG structure such as circular PBG [14,15], triangular structure [16], meta-material structure [17,18], and surrounded structures [19] have been reported in recent literature. In addition, defected ground structure (DGS) [20] is another prominent method to achieve band-stop features and bandwidth enhancement.

This paper presents a novel design of a PBG substrate-based THz microstrip patch antenna; its performance was benchmarked with the recently reported THz patch antennas mounted on the homogeneous substrate. Different design parameters such as substrate height, patch shape, and radius of the patch were parameterized and optimized to achieve the best radiation performance. The paper is organized as follows: Section 2 presents the design of the proposed antenna. Following that, Section 3 presents the simulation results and related analysis. Finally, the conclusion of this article is given in Section 4.

2. Proposed Antenna Structure

This section covers the design details of the convention and proposed PBG-based antenna, intended for applications in the THz frequency band. Polyimide was used as a substrate material, having a loss tangent of 0.0025 and a dielectric constant of 3.5. The overall volume of the antenna was 700 × 660 × 192 μm³. Furthermore, the design details of the presented THz antenna based on three different types of PBG substrate are also discussed. From now onwards, the following naming nomenclature will be used to differentiate between the different variants of the antenna that are discussed in this manuscript:

Type-A: THz antenna backed by a homogeneous substrate, shown in Figure 1a.

Type-B: THz antenna backed by PBG substrate with rectangular shape metallic insertions as shown in Figure 1b.

Type-C: THz antenna backed by PBG substrate with triangular shape metallic insertions, shown in Figure 1c.

Type-D: THz antenna backed by PBG substrate with circular shape metallic insertions, shown in Figure 1d.

The structural parameters of the four types of antennas are listed in

Table 1. Design Parameters of the THz antennas.

Parameter	Value (μm)	Parameter	Value (μm)	Parameter	Value (μm)
Lg	700	Rc	100	Wr	25
Wg	660	Rh	75	Sr	95
Lf	240	Sc	95	Lr	20
Wf	105	R	16	St	95
Wt	85	R0	80	***	***

*** = Not Given.

. The Type-A antenna in Figure 1a is based on a homogenous substrate and is used as a reference antenna to evaluate the performance of the other antennas. Type-B, shown in Figure 1b, is a THz antenna backed by PBG substrate with rectangular shape metallic insertions sized 25 × 20 um and separated by 95 um. Figure 1c is a Type-C THz antenna backed by PBG substrate with equilateral triangular shape metallic insertions with side length “W_t” and separated by 95 um. Type-D, shown in Figure 1d, is a THz antenna backed by PBG substrate with circular shape metallic insertions with radius “r” and separated by 95 um. Figure 1e shows the inner view of the substrate layer after insertion of the array of PBG unit cells. Later, it will be shown from the results that the Type-D provides the optimum performance compared to other designs; the dimensions of the antenna were obtained using well-known microstrip antenna theory [20] for the given frequency (f_r) in hertz (Hz), a substrate of dielectric constant (ε_r), and height (h_s) in units of centimeters. The effective radius of the antenna (R_c) was obtained from the actual circular patch radius (a) using the following equations [21]:

$$a=\frac{F}{{\left\{1+\frac{2h_s}{\pi {\epsilon }_{r}F}+[ln(\frac{\pi F}{2h_s})+1.7726]\right\}}^{1/2}}$$

(1)

where F is $8.791\times {10}^9/f_r\sqrt{{\epsilon }_r}$. The effective radius of the antenna can be expressed as

$$Rc=a\sqrt{1+\frac{2h}{\pi a}\left(ln\left[\frac{a}{2h}\right]+1.7726\right)}\mathrm{a}$$

(2)

where f_r denotes the operating frequency in Hz, ε_r is the relative dielectric constant, and ε_reff is the effective dielectric constant. Computation of width (W_f) of the feed line is based on the input impedance (Z_a) of the antenna, given by:

$$Z_a=\frac{11.96 {\lambda }_0}{W_f}$$

(3)

The input impedance (Z_a) was matched with the standard 50 Ω impedance through a feeding line of length, L_f. The characteristic impedance of the feed line was Z₀ = 50 × Z_a. The width of the feed line was obtained using:

$$W_f=\frac{7.475h_s}{e^x}-1.25t$$

(4)

$$x=\frac{Z_0\sqrt{{\epsilon }_r+1}}{87}$$

(5)

where h_s and t are the height of substrate and thickness of the patch, respectively.

The development of the design was performed in steps shown in Figure 2, which produced a different set of return loss characteristics as demonstrated in Figure 3. The value of R₀ was optimized to 80 µm to achieve lowest return loss at the resonating frequency. Changes were made for improvement in antenna performance in terms of driving point impedance bandwidth and the return loss. Figure 3 depicts that step 1 was designed by designing a circular patch that gave a resonance frequency of 0.62 THz. In step 2, the circular patch was reduced to half-moon by subtracting half of the circle from the top, with an operating frequency of slightly higher than 0.63 THz. An octagon was embedded at the top of the half-moon shape in order to achieve the final design with better results in step 3, having the resonance frequency of 0.63 THz.

3. Simulation Results and Discussion

The radiation characteristics of the proposed antennas were examined in the frequency range of 0.60 to 0.75 THz using the Finite Integration Technique (FIT) available in CST Microwave Studio [22]. The performance of the antennas was analyzed in terms of return loss, gain, directivity, impedance bandwidth, VSWR, and radiation efficiency.

Table 2. Simulation parameters for the analysis of the proposed design.

Type	Parameter	Unit	Value
Simulation solver	Solver type		Finite Integration technique
	Impedence	Ohm	50
	Mesh type for time Domain Solver		Hexahedral
	Frequency Range	THz	0.6 to 0.7
Polyimide substrate	Relative permitivity	Unitless	3.5
	Density (rho)	Kg/m3	1400
	Young’s Modulus	GPa	2.5

lists the simulation parameters for the performance analysis. It is evident from Figure 4 that Type-A and D antennas resonated at 0.63 THz, with −10 dB bandwidths of 28.88 GHz and 29.79 GHz, respectively. The resonant frequency of the Type-B antenna was slightly shifted upwards to 0.6233 THz, giving a −10 dB bandwidth of 26.47 GHz. The Type-C antenna gave peak resonance at a lower frequency of 0.626 THz with a −10 dB bandwidth of 27.84 GHz. This comparison shows that the Type-D antenna provided wider bandwidth as compared to the other candidate antennas.

As shown in Figure 5, the VSWR of the four antennas was found to be less than 1.5 within the operational bandwidth of the antennas, which shows that the antennas were optimally matched to the feed line. It can be observed in Figure 6 that the Type-D antenna gave a better peak gain of 9.45 dB at the resonant frequency for wider bandwidth, as compared to the rest of the three THz antennas. The comparison of the radiation efficiency plots in Figure 7 shows that the PBG-based THz antennas are more efficient (87–90%) as compared to the Type-A THz antenna, which was based on a homogeneous substrate with a radiation efficiency of 80%. The better efficiency of the PBG-based antennas is due to the suppression of the surface waves by the PBG structure.

A simple equivalent circuit model for proposed compact size THz antenna was designed and then simulated in advanced designed system (ADS) software as shown in Figure 8, which provides an equivalent input impedance matching that of the antenna. The equivalent circuit consisted of one RLC (resistor–inductor–capacitor) parallel circuit connected in series with two resistors: an inductor and a capacitor. The use of resistors improves the reflection coefficient to less than −10 dB. The reflection coefficient of the THz antenna can be tuned by varying the values of the capacitors and inductors. Comparison of the reflection coefficients for the proposed antenna S₁₁ with that of the circuit model is presented in Figure 9, which shows good agreement between the two sets of results.

The three-dimensional radiation patterns of the THz antennas are illustrated in Figure 10, which shows that the Type-D antenna offered the highest gain (9.45 dB) at 0.63 THz, as compared to the rest of the antennas. The two-dimensional radiation pattern of the antennas in the two principal planes (E-plane and H-plane) is portrayed in Figure 11. The radiation pattern of the antennas was relatively broader in the H-plane as compared to the E-plane. The results show that the peak gain of the antennas occurred at 90°, with the highest half-power beamwidth of 105° for the Type-D antenna.

In Figure 12a,b, the electric field distribution of Type-A and Type-D antennas at a frequency of 0.63 THz is presented. It is observed that the electric field intensity at the upper and lower edges of the proposed modules was more intense than in the central region.

4. Parametric Analysis

Based on the analysis in the previous section, it is evident that the Type-D antenna gives better radiation characteristics at 0.63 THz as compared to other candidate antennas. The effect of varying the hole radius (r) of the PBG unit cell on the return loss and gain of the proposed Type-D antenna was investigated. An increase in the radius of the hole resulted in a proportional increase in the resonant frequency as shown in Figure 13a. It can be observed that radii of 16 μm provided the optimum value of return loss (−60 dB) at 0.63 THz. For a radius of 28 μm, the resonant frequency was shifted to 0.66 THz with a larger value of return loss (−28 dB). The gain variation with change in radii is shown in Figure 13b, which verifies that the highest value of peak gain (9.45 dB) was achieved at 0.63 THz if the radius was set equal to 16 μm. A proportional drop in gain was observed if the radius was increased above this value. The performance metrics of the THz antennas presented in this manuscript are compared in

Table 3. Comparison of the proposed antenna with sate of the art work.

Particular	fr (THz)	S11 (dB)	BW (GHz)	Gain (dB)	Directivity (dBi)	VSWR	Rad: Efficiency
[23]	1.04	−17.59	***	7.99	8.24	***	91.1
[24]	0.96	−15.70	***	***	***	1.39	***
[25]	0.690	−34.9	24	6.88	7.01	1.043	***
[26]	0.703	−50.94	26.4	5.24	6.81	1.005	***
[27]	0.6308	−44.71	36.23	7.94	8.61	1.012	85.7
This work (Type-A)	0.63	−28.49	28.88	8.34	8.9	1.02	82.6
This work (Type-B)	0.633	−53.11	26.47	8.96	9.48	1.07	88.6
This work (Type-C)	0.626	−47.79	27.84	9	9.5	1.04	89.5
This work (Type-D)	0.63	−59.15	29.79	9.45	10.1	1.0001	90.6

*** = Not Given.

with other antennas proposed in the recent literature [23,24,25,26,27]. The comparison shows that the proposed antenna gives improved results in terms of gain, directivity, bandwidth, and radiation efficiency. It can be observed in the comparison that the performance of the Type-D antenna among the proposed designs is better in terms of gain, VSWR, directivity, and return loss at the resonance frequency of 0.63 THz. As polyamide-based antennas are more affected by the humidity as compared to FR4 or RT/Duroid material, the relative permittivity of the substrate increases with the absorption of water. The amount of absorption depends on the temperature and moisture level, as well as the structural design of the substrate. The compactness and hole-based design of the proposed antenna makes it suitable to be used in humid conditions, similar to the recently proposed breathable antennas [28]. Fabrication and testing of THz antennas at such high frequency range requires high-cost facilities which were not available to the authors at the time of publication. In addition to the cost, fabrication of a highly efficient coupling port (between the source and the antenna) and the required ultra-high precision for thin substrates is still an issue, even with the use of special procedures such as the batch processing mechanism [29]. Fabrication constraints for THz antennas need to be considered during the design process. The compactness of the device and requirement of special fabrication environment makes it costly and challenging as this process consists of substrate preparation, antenna pattering over the substrate, and testing. Recent developments in electron-beam lithography allows sub-micron dimensions for such devices, but for feeding mechanism, waveguide-fed or probe-fed with a probe station, a highly efficient coupling port (between the source and the antenna) is still a difficult task to achieve. In addition, antenna gap geometry is another challenging factor, which is the space where the electron–hole pairs are generated and coupled to the antenna electrodes, making the fabrication accuracy very important to avoid electric short circuit.

5. Conclusions

In this paper, multiple variants of a planar THz antenna operating at 0.63 THz were designed using different types of PBG-based substrates. For comparison purposes, a similar antenna with a homogeneous polyimide substrate was used. It was observed that better gain (>9.4 dB), directivity (>10 dB), and impedance bandwidth (>29 GHz) were achieved by the proposed antenna with Type-D, which is backed by the circular-shaped unit cell PBG substrate. The effects of varying the radii of the circular insertions on the return loss and gain of the antenna were investigated. The THz antennas reported in this work are compared with other reported THz antennas and results show the improvement in terms of gain and bandwidth. Thus, the antenna can be a prospective candidate for modern THz applications, such as spectroscopy, sensing, medical diagnosis, and high data rate wireless hotspots.